10. A well-fitting piston with 4 small holes in a sealed water-filled cylinder, shown in the figure, is pushed to the right at a constant speed of 4 mm/s while the pressure in the right compartment remains constant at 50 kPa gage. Disregarding the frictional effects, determine the force F that needs to be applied to the piston to maintain this motion. Ans: 0.565 kN d₁-3 cm Water Piston d₂= 12 cm Hole d = 2 mm P-50 kPa Cylinder

10. A well-fitting piston with 4 small holes in a sealed water-filled cylinder, shown in the figure, is pushed to the right at a constant speed of 4 mm/s while the pressure in the right compartment remains constant at 50 kPa gage. Disregarding the frictional effects, determine the force F that needs to be applied to the piston to maintain this motion. Ans: 0.565 kN d₁-3 cm Water Piston d₂= 12 cm Hole d = 2 mm P-50 kPa Cylinder

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem (2) Neglecting friction, find the horizontal force of the water (N) on the horizontal bend shown in the figure. V, = 10 m/s %3D 8 cm dia. V2 4 cm Answer:
3. (a) A nozzle of inlet area A₁ and exit area A2 exhausts to atmosphere. A fluid of density p enters the nozzle with pressure p₁ (gauge) and velocity u₁. Show that the force trying to separate the nozzle from the pipe is given by 2 F = P₁A₁ - pA₁u₁² whether the nozzle is frictionless or not. A₁ A₂ -1)
The horizontal nozzle in Figure has D; - 12 cm and D2 - 4 cm, with inlet pressure p1 200 KPa absolute and V2 - 10 m/s. For water at 20°C and density of 1000 kg/m3, compute the horizontal force provided by the flange bolts to hold the nozzle fixed. The atmospheric pressure is 100 KPa. Open jet Water
A scuba tank is dropped overboard and sinks to the ocean floor 20 ft below (T = 62 F). The composite metal (SG = 4.5) tank has a mass of 31.7 lbm when empty and has an internal volume of 0.355 ft3. The tank is currently filled with air to about 3000 psig. To retrieve the tank, you plan to dive down, open the valve, and let out air until the tank begins to float upward. Then, I realized that my plan to float the tank by letting out air wouldn't work. My second thought is to swim down, attach an empty plastic bag to the air valve, and release air from the tank into it. Will this work? If so what will be the volume of air in the bag when the tank just lifts off the ocean floor (ft3) and what will be the mass of air in the bag?
3600s Table 1-2, 1 ft = 0.304 8m. Thus, 0.556m 1 ft 0.556m/s = 0.3048m =1.82 ft / s Note: Remember to round off the final answer to three significant mple 2: Convert the quantities 300 lb.s and 52 slug/ft° to appropriate S ation: Using Table 1-2, 1 lb =4.448 2 N 4.448N 300 lb.s = 300 lb.s * 1 lb 1334.5N.s 1.33KN.s %3D 14.593 8 kg and 1 ft = 0.304 8 m, then
Water flows inside a horizontal pipe so that at the beginning of the pipe it’s velocity v1 is lower than the velocity at the end of the pipe v2. Compare the pressures at the beginning P1 and at the end of the pipe P2: A. P1 > P2 B. Not enough information
an airplane is flying at a 4000 m elevation where the temperature is -11C and the density of air is 0.82 kg/m3. The pitot tube “manometer” (pressure transducer) measures 30.8 mm Hg. Find the speed of the plane
A fan when driven by a 5.8 Hp motor at a speed of 800 rpm delivers 510 m3/min at a total pressure of 5 cm water gage. If in the same installation, 6.5 cm water gage pressure is required. What power will the fan be driven?
A scuba tank is dropped overboard and sinks to the ocean floor 20 ft below (T = 62 F). The composite metal (SG = 4.5) tank has a mass of 31.7 lbm when empty and has an internal volume of 0.355 ft3. The tank is currently filled with air to about 3000 psig. To retrieve the tank, you plan to dive down, open the valve, and let out air until the tank begins to float upward. Will this work? If so, what will be the pressure in the tank (psig) when the scuba tank first lifts off the ocean floor? If not, why not?
Water is flowing in a fire hose from point A with a velocity of 10 m/s and a pressure of 300 kPa as illustrated in figure below. There is changes in height of 20 m from point A to B. The velocity at point A and B is the same. Use the Bernoulli equation to calculate the pressure of the water at point B and C respectively. The density of water is 1000 kg/m³ and gravity is 9.8 m/s?. VA = 10m/s A = 3m? A Pa = 300kPa h= 20m B C Ac = 6m? Ag = 3m?
A room has a volume of 349 m3. An air-conditioning system is to replace the air in this room every 81.5 minutes, using ducts that have a square cross section. Assuming that air can be treated as an incompressible fluid, find the length of a side of the square if the air speed within the ducts is (a) 2.00 m/s and (b) 7.00 m/s. a: b:
4m A 4-meter-diameter cylindrical tank contains oil and water as shown in the figure. At the bottom of the tank is an orifice having a diameter of 0.1 meter with coefficient of contraction and coefficient of velocity equal to 0.62 and 0.98, respectively. Determine the following: 6m Oil, SG = 0.9 a. The rate of flow on the orifice (L/s). b. The time to remove water only at the tank (s). c. The time to drain all the liquids (s). 4m Water