2. Sketch the ac equivalent circuit for the amplifying system, as shown below, using r-model. And calculate the following ac performance quantities for the amplifier circuit given below. Use r-analysis with B = 150 and ß = 120. a. Voltage gain b. Current gain c. Input impedance d. Overall Voltage gain (A,) 15V R1 R2 4.TK 200K C2 100uF C1 R5 1K 100uF C3 100uF Q1 V1 10V / 1Hz R3 2.2K R4 10K

2. Sketch the ac equivalent circuit for the amplifying system, as shown below, using r-model. And calculate the following ac performance quantities for the amplifier circuit given below. Use r-analysis with B = 150 and ß = 120. a. Voltage gain b. Current gain c. Input impedance d. Overall Voltage gain (A,) 15V R1 R2 4.TK 200K C2 100uF C1 R5 1K 100uF C3 100uF Q1 V1 10V / 1Hz R3 2.2K R4 10K

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. The average power consumed by a resistance is equal to .. in non- .... ... sinusoidal input signal. *
1. The DC-DC converter has several circuit configurations. a) (Draw a simple connection of IGBT switch, diode and inductor that can discriminate between Buck, Boost and Buck-Boost converter circuits respectively.) b) ('A Boost converter produces an output voltage, Vo that is more than or equal to the input voltage, Vi. Based on this statement develop the equation for the relationship between Vo Viand D. where D represents the duty ratio. You can use any suitable diagram to illustrate your answer.)
One of the following is not a property of a common-emitter amplifier: Select one: a. high voltage gain b. No phase inversion c. high current gain d. Emitter is at ac ground
Write the expression for the output voltage of a balanced modulator
Draw the AC equivalent circuit and find Zi, Zo, Av, Ai (ignore the effect of To). Show all the necessary derivations and label all the parameters properly.
Q.4. A single-phase half-wave-controlled converter is operated from a 120V, 50HZ supply. Load resistance R = 100. If the average output voltage is 25% of the maximum possible average output voltage, determine: (a) Firing angle (b) RMS and average output currents (c) Average and RMS SCR currents. Also draw the waveforms.
QUESTION 1 Design a high efficiency 3.3 V, 5A d.c.to d.c. power converter from a 4 to 5.5 Vdc source. The maximum allowable inductor current ripple and output voltage ripple are 0.1A and 20 mV, respectively. Assume a switching frequency of 20 kHz. a) Design a suitable converter power circuit using a MOSFET switch, showing all calculation of inductor and capacitor values and drawing a circuit diagram of the final design including component values. Indicate the peak inverse voltage and forward current rating of any diode required, and the maximum drain- source voltage of the MOSFET. b) On the Schematic diagram, draw the path of the current flow during the ON time and the OFF time. c) Describe the effect of changing the values of the inductor and the capacitor in the circuit. d) What is the effect of switching frequency in the circuit? e) Draw the schematic diagram of a circuit with the output voltage higher than the input voltage.
With an aid of a. c. equivalent circuit, derive an equation representing common- mode gain (Ac) of the circuit.
In digital frequency meter, output of amplifier is applied to the.........
Input voltage of a boost converter 80 V, output voltage 140 V and switchingits frequency is 20 kHz. The converter efficiency is known to be 95%.a) Continuous conduction (current) in operation when the load resistance changes between 14 - 20ohmThe lowest inductance (L) value and output that should be used to maintain the operation.the peak-to-peak value of the voltage ripple should be used to be 2% of the output voltage.Calculate the capacitor's capacity (C).
Find the following: DC gain, inductor current ripple and output voltage ripple: For DC-DC Buck converter: 1-Draw all circuits in all position 2-Sketch the transistor current waveform 3-Derive analytical expressions for the dc components of the capacitor voltages and inductor currents. 4-Derive analytical expressions for the peak ripple magnitudes of the input filter inductor current and capacitor voltage.
Draw and derive the relation between input and output voltage of buck-boost converter in terms of duty factor.