3. A beam ABCDE is 16 m long and is simply supported at A and D 14m apart. At B, 4 m from A, there is a concentrated load of 30kN and a uniformly distributed load of 5kN is carried over the position AC which is 10 m long. A further concentrated load of 10KN is carried at E on an overhang 2 m from D. Draw the shear force and bending moment diagrams indicating the maximum values on each.

3. A beam ABCDE is 16 m long and is simply supported at A and D 14m apart. At B, 4 m from A, there is a concentrated load of 30kN and a uniformly distributed load of 5kN is carried over the position AC which is 10 m long. A further concentrated load of 10KN is carried at E on an overhang 2 m from D. Draw the shear force and bending moment diagrams indicating the maximum values on each.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.10.1P: A heavy object of weight W is dropped onto the midpoint of a simple beam AB from a height h (see...

See similar textbooks

Similar questions

A heavy object of weight W is dropped onto the midpoint of a simple beam AB from a height h (see figure). Obtain a formula for the maximum bending stress ^ma* due to tne filing weight in terms of h, st, and 5st, where it is the maximum bending stress and Sstis the deflection at the midpoint when the weight W acts on the beam as a statically applied load. Plot a graph of the ratio o"max/ö"it (that is, the ratio of the dynamic stress to the static stress) versus the ratio iifS^r(Let h/S^ vary from 0 to 10.)
Q2/ A beam AB of span 9m is simply supported at the ends. The beam carries point load of 2KN upwards at 2m from A and a uniformly distributed load (UDL) of 1000 N/m downwards on a length of 6m from B. Determine the Support reactions?
Problem 3: A bent beam ABCD is held in equilibrium by a roller at A and by a pinned connection at D. The beam supports a uniform distributed load (80 lb/ft) over section AB and a concentrated force (390 lb) at point C. The roller at A rests against an inclined surface that is oriented 30° from the horizontal direction. Neglect the weight and depth of the beam and the size of the roller in this analysis. (a) Draw a complete FBD of beam ABCD. Clearly label all loads, reactions, and distances. (b) Determine all reactions at A and D. 80 lb/ft 30°/ 8 ft B 4 ft D 390 lb 12/12 3 ft
A bending moment due to load applied on the head of femur bone which is offset by a distance (x= 50 mm) off the bone center for a person standing in relaxation.His weight is 70kg.1. Find the maximum bending stress induced due to the weight and compare it to the maximum comp. stress. R= 20mm t= 12mm.2. Draw the expression for the second moment (I) basing on min-wall hollow cylinder.3. Find the principal stress σ1, σ2, τx1y1, and the angle θp for point C and D shown.
A beam of size 150 mm wide, 250 mm deep carries a uniformly distributed load of w kN/m over entire span of 4 m. A concentrated load 1 kN is acting at a distance of 1.2 m from the left support. If the bending stress at a section 1.8 m from the left support is not to exceed3.25 N/mm2 find the load w.
5.41 The inverted T-beam supports three concentrated loads as shown in the fig- ure. Find the maximum allowable value of P if the bending stresses are not to exceed 4 ksi in tension and 10 ksi in compression. 3P 1.0 in. E 8 in. 1.0 in. 6 ft - 6 ft 4 ft e 4 in.- 4 ft
5.41 The inverted T-beam supports three concentrated loads as shown in the fig- ure. Find the maximum allowable value of P if the bending stresses are not to exceed 4 ksi in tension and 10 ksi in compression. 1.0 in - 8 in. 1.0 in. 4 ft 6f - 4 ft - 6 ft-
Q2/ A beam ABCD, 6 m long, is simply-supported at the right-hand end D and at a point B 1m from the left-hand end A. It carries a vertical load of 10 kN at A, a second concentrated load of 20 kN at C, 3 m from D, and a uniformly distributed load of 10 kN/m between C and D. Draw shear force and bending moment diagram.
A simply supported beam is shown. The maximum bending moment is at B. Use the method of sections to determine the moment at B. Then determine the required section modulus needed for an allowable bending stress of 24 ksi. Verify that two L4x3 angles placed as shown will support the loading based on the angle thickness you select using Appendic C. Ans: Ms = 4350 Ib-ft %3D 2000 Ib 300 lb/ft 6 in, CTI 4 in. 3 ft 3 ft
Example The beam ABC is loaded via a 500 N.m couple and a 600 N force as shown. The beam is connected to the rest of the system by a pin joint at B and a roller support at C. Detemine the magnitude of the reaction forces on the beam at the supports. 600 N 500 N.m 400 300 500 Ans. RC=1700 N RBx=1597.5N Dimensions in mm REDMI NOTE 9 PRO AI QUAD CAMERA RBy=1181.4 N
For a beam subjected to the load F at the center of the span as shown below, please 1. Find the maximum allowed load F, given a. Modulus of Rupture (MOR) of the material for the beam = 130 GPa b. Beam width b = 0.02m and depth d = 0.05m c. Span length L = 10m 2. If the maximum allowed load F is designed to be 40,000N, given all other conditions the same, what is the minimum MOR required for the material to make the beam? 3. If the maximum allowed load F is designed to be 50,000N, given all other conditions (MOR = 130 GPa) the same, what is the minimum depth d required? F b ✰ d ↓ D L
A symmetric frame PQR consists of two inclined members PQ and QR, connected at 'Q' with a rigid joint, and hinged at 'P' and 'R'. The horizontal Length PR is L. If a weight W is suspended at 'Q', the bending moment at 'Q' is