3. A simple connecting rod mechanism has a rod 250mm long and a crank radius of 75 mm. The connecting rod has a mass of 1.5kg, its centre of gravity is 75mm from the large end and it has a radius of gyration about the centre of gravity of 100mm. When the crank angle is 30° and the crankshaft speed is 3000rpm clockwise: (a) (i) Show by kinematic analysis that the angular acceleration of the connecting rod is 13,940 rad/s² (clockwise) (ii) Show also that the acceleration of the centre of gravity (C) in the X and Y direction is respectively, fcx = 6759m/s² (to the right) and fcy = 2590.8m/s² (downwards). Hence, find the magnitude and direction of the forces acting on the frame of the engine due to the inertia of the connecting rod as follows: (b) The force exerted by the cylinder wall on the piston at B (c) The force on the main bearing at O (d) The torque input or output at the crank B Figure 3. Connecting rod mechanism C A 30° O

3. A simple connecting rod mechanism has a rod 250mm long and a crank radius of 75 mm. The connecting rod has a mass of 1.5kg, its centre of gravity is 75mm from the large end and it has a radius of gyration about the centre of gravity of 100mm. When the crank angle is 30° and the crankshaft speed is 3000rpm clockwise: (a) (i) Show by kinematic analysis that the angular acceleration of the connecting rod is 13,940 rad/s² (clockwise) (ii) Show also that the acceleration of the centre of gravity (C) in the X and Y direction is respectively, fcx = 6759m/s² (to the right) and fcy = 2590.8m/s² (downwards). Hence, find the magnitude and direction of the forces acting on the frame of the engine due to the inertia of the connecting rod as follows: (b) The force exerted by the cylinder wall on the piston at B (c) The force on the main bearing at O (d) The torque input or output at the crank B Figure 3. Connecting rod mechanism C A 30° O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The dimensions of the various links of a mechanism, as shown in Fig. 3, are as follows: OA = 0.3 m: AB = 1 m: CD = 0.8 m; and AC = CB. If the crank OA rotates at 100 rpm. in the anticlockwise direction, find, for the given configuration: 1. velocity and acceleration of B and D: 2. angular acceleration of the links AB and CD. 45 0.6 m- Eig 3
The turning moment diagram for a petrol engine is drawn to the following scales : Turning moment, 1 mm = 5 Nm; crank angle, 1 mm = 1°. The turning moment diagram repeats itself at every half revolution of the engine and the areas above and below the mean turning moment line taken in order are 295, 685, 40, 340, 960, 270 mm. The rotating parts are equivalent to a mass of 36 kg at a radius of gyration of 150 mm. Determine the coefficient of fluctuation of speed when the engine runs at 1800 r.p.m.
The crankshaft of a vertical sıngle-cylinder engine, stroke 250 mm, rotates at 300 r/min The reciprocating parts ( including part of the connecting rod) have a mass of 100kg The connecting rod has a mass of 120 kg, it is 450 mm long, the centre of mass is 300 mm from the gudgeon pin axıs and the radiųs of gyration about the same axıs is 363 mm When the crank is 30° from the t dc position and moving downwards, determine 31 the side thrust on the cylınder walls due to the inertia of the reciprocatıng parts, and 32 the crankshaft torque on the crankshaft due to inertia
A four-cylinder vertical engine has cranks 150mm long. The plane of rotation of the first, second and fourth cranks are 400mm, 200mm and 200mm respectively from that of the third crank and their reciprocating masses are 50kg, 60kg and 50kg respectively. Find the mass of the reciprocating parts for the third cylinder and relative angular position of the cranks in order that the engine may be in complete balance.
The crankshaft of a vertical engine, stroke 250 mm, rotates at 300 rpm. The reciprocating parts have a mass of 100 kg. The connecting rod has a mass of 120 kg, it is 450 mm long, the C.G is 300 mm from the gudgeon pin axis and the radius of gyration about that axis is 363 mm. When the crank is 30o from the TDC position and moving downwards, find:-The total kinematic energy of the connecting rod
A flywheel is fitted to a multi cylinder engine, which runs at a mean speed of 360 r.p.m. If the speed varies from 6 % above the mean to 2 % below it and the fluctuation energy is 1200 kN-cm, If the radius of gyration is 20 cm, find (i) mass moment of inertia of the wheel and (ii) mass of flywheel. The mass moment of Inertia in Kgm2 is Mass of the flywheel in kg is
a) An anemometer for measuring the wind speed consists of three thin, hemispherical shells of mass Meach and three connecting rods of mass mas shown in Figure Q1a. If the mass moment of inertia of the thin hemispherical shell about its centre of mass, axis GG' is given by 12 5 Ma? where a is the inner radius of the hemispherical shell. Find the mass moment of inertia of the anemometer about the axis AA'. Give your answer in terms of M, m, a and I. Consider the central rod as a thin rod. b) If the anemometer is rotating at 4 rev/sec. The system parameters are given as M=200g, m=90 g, a=40 mm and l=0.3m find the rotational kinetic energy and angular momentum. A' G
A dancer is spinning at 72 rpm about an axis through her center with her arms outstretched, as shown in (Figure 1). From biomedical measurements, the typical distribution of mass in a human body is as follows: Part A Head: 7.0% Arms: 13% (for both) Trunk and legs: 80.0% Calculate moment of inertia about the dancer's spin axis. Express your answer with the appropriate units. Suppose the mass of the dancer is 64.5 kg, the diameter of her head is 16 cm, the width of her body is 24 length of her arms is 60 cm. cm, and the HÀ ? I = Value Units Submit Request Answer Figure 1 of 1 > Part B Calculate dancer's rotational kinetic energy. Express your answer with the appropriate units. ? K = Value Units Submit Request Answer
The single slider mechanism shown below has the following dimensions: the crank AB - 95 mm and the connecting rod BC-270 mm with centre of gravity D, 90 mm from B. The crankshaft has a speed of 75 rad/s and an angular acceleration of 1200 rad/s. Find: Acceleration of D and angular acceleration of CB. 125
A car is moving on a curved horizontal road of radius 100 m with a speed of 20 m/s. The rotating masses of the engine have an angular speed of 100 rad/s in clockwise direction when viewed from the front of the car The combined moment of inertia of the rotating masses is 10 kg-m².what is the magnitude of the gyroscopic moment in (N-m)?
Each problem requires a proper FBD and separate kinematic diagram. 1. The drum has a weight of 90 lb and a radius of gyration of 0.42 ft. If a cable is wrapped around the drum and given a force of 8 lb, how long does it take to increase the drums angular velocity from 10 to 20 rad/s? Neglect the mass of the cable. 0.5 ft
Q3- In the schematic drawing in Figure below, the change in the forward angular momentum during the gyroscopic effect is 7 kg m/s², and it was found that the product of the orthogonal velocities is equal to two hundred rad/ s?; determine 1- mass moment of inertia of rotor, 2- If you look at the ship from the port, is the ship sailing to the right or left (draw the ship to clarify your answer) ?, and 3- what is the effect of GC on the ship?. 1 Dr. Haider Khazal, TOM-1, 2021, Preliminary questions to the final exam COUPLE VECTOR SPIN VECTOR ACTIVE GYROSCOPIC ROTATED BY 90 REACTIVE GYROSCOPIC COUPLE VECTrOR SPIN VECTOR PRECESSION VECTOR