A 1.625-in-diameter solid steel shaft supports loads PA- 400 lb, Pc- 600 lb, and PE- 400 Ib, as shown. Assume that LAAB - 11 in., Lạc 23 in., Lco - 13 in., and LoE 16 in. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of the maximum bending stress in the shaft. LAN Lục Pc ksi Answer: amas =

A 1.625-in-diameter solid steel shaft supports loads PA- 400 lb, Pc- 600 lb, and PE- 400 Ib, as shown. Assume that LAAB - 11 in., Lạc 23 in., Lco - 13 in., and LoE 16 in. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of the maximum bending stress in the shaft. LAN Lục Pc ksi Answer: amas =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a = 280mm, b = 170mm, c = 80mm, and θ = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 29 mm. Determine the bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest tenths.
P 130 mm 25 mm 25 mm P P 3. Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
The assembly consists of two posts AD and CF made of steel and having cross- sectional area of 1000 mm², and an aluminium post BE having a cross-sectional area of 1500 mm². If a central load P is applied to the rigid member ABC, determine the normal stress in each post. Take elastic modulus of steel and aluminium as 200 GPa and 70 GPa, respectively. PKN P [kN] -0.5 m- Last digit of Student ID 0, 1, 2, 3, 4 5,6,7,8,9 500 700 e.g. SID 21051234 P=700 A B -0.5 m C 0.4 m F Fig. 1-1 System with three posts Last digit
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
12-2. The L2 steel blade of the band saw wraps around the pulley having a radius of 12 in. Determine the maximum normal stress in the blade. The blade has a width of 0.75 in. and a thickness of 0.0625 in. Prob. 12-2 12 in.
The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T₁ = 50°F, determine the average normal stress in each member when T₂ = 120°F. Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in². 3 ft B 2 ft
The bar of the pin connected frame shown are each 30mm by 60mm in section. determine the maximum load P that can be applied so that the stress will not exceed 100MN/me in tension or 80 MN/me in compression
Two plates with a thickness of 35mm, width of 160mm, and length of 200mm are joined together by a pin with a diameter of 60mm. 200 mm 60 mm P 160 mm T 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250MPA and the shear strength of the pin is 100MPA. Suppose that P is 140KN, the Modulus of Elasticity is 200GP,, and the Poisson's ratio is 0.3. 2) Determine the change in length of each plate. 3) Determine the change in width of each plate. 4) Determine the change in thickness of each plate.
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
4 in 7/8 in 7/8 in 2. The lap joint shown in the figure, is fastened by four 25mm.-diameter rivets. Calculate the maximum safe load P in N that can be applied if the shearing stress in the rivets is limited to 80 MPa and the bearing stress in the plates is limited to 120 MPa. Assume the applied load is uniformly distributed among the four rivets.
Q-The internal diameter of a shaft of steel is 70% of the external diameter. The shaft is to transmit 3500 kW at 200 rpm. If the maximum allowable stress in the shaft material is 50 MPa, find the diameter of the shaft. Take length of the shaft=4 m & G=80 MPa. Also calculate the maximum twist of the shaft when it is stressed to the maximum permissible value.
A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of 12 inch in diameter, and four – ¾ inch aluminum bolts on a concentric bolt circle 8 inches in diameter. With an applied torque of 260 kips*inch. determine the max shearing stress in the aluminum and steel bolt. Use Gst = 12x10 6 psi and Gal = 4x106 psi