Please do not rely too much on chatgpt, because its answer may be wrong. Please consider it carefully and give your own answer. You can borrow ideas from gpt, but please do not believe its answer.Very very grateful!Please do not rely too much on chatgpt, because its answer may be wrong. Please consider it carefully and give your own answer. You can borrow ideas from gpt, but please do not believe its answer.and and Very very grateful! (a) A light canopy AB is hinged at A and suspended by cable BD at B, receiving the load as shown in the figure.When d=200 mm, calculate (a) the tension in cable BD, and (b) the reaction at A.(b) A light canopy AB is hinged at A and suspended by cable BD at B, receiving the load as shown in the figure.When d 150 mm, calculate (a) the tension in cable BD, and (b) the reaction at A.=A90 ND100 mm90 NB100 mm→-100 mm→1+1100 mm →

Step 1: Draw FBD of the given system From triangle ABE as per above…

(a) A light canopy AB is hinged at A and suspended by cable BD at B, receiving the load as shown in the figure. When d=200 mm, calculate (a) the tension in cable BD, and (b) the reaction at A. (b) A light canopy AB is hinged at A and suspended by cable BD at B, receiving the load as shown in the figure. When d 150 mm, calculate (a) the tension in cable BD, and (b) the reaction at A. = A 90 N D 100 mm 90 N B 100 mm→ -100 mm→ 1+1 100 mm →

(a) A light canopy AB is hinged at A and suspended by cable BD at B, receiving the load as shown in the figure. When d=200 mm, calculate (a) the tension in cable BD, and (b) the reaction at A. (b) A light canopy AB is hinged at A and suspended by cable BD at B, receiving the load as shown in the figure. When d 150 mm, calculate (a) the tension in cable BD, and (b) the reaction at A. = A 90 N D 100 mm 90 N B 100 mm→ -100 mm→ 1+1 100 mm →

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B, C, and D. If the tension in wire AB is 110 lb. (a) Determine the vertical force P exerted by the tower on the pin at A. (b) Determine the moment about point o of the Resultant Force. 25 ft 20 f 100 ft 60 ft D 20 ft 18 ft 74 ft
240 600 (d) (e) Problems 3.1 Each of the bodies shown is in equilibrium, homogeneous and has a mass of 30 kg Assume frictionless at all contact surfaces. Draw the fully dimensioned FBD for each body and compute the horizontal and vertical components of all forces acting on each of the members. Cable 1.2 m 0.9 m 0,6 m Cable 30 800 N/m 1.5 m 30° 30° 3.2 The homogeneous beam AB weighs 400 lb. For each support condition shown
The rigid bars shown are separated by a roller at C and pinned at A and D. A steel rod at at B helps support the load P. Determine the vertical movement of the steel rod Given: 3 m B ast Steel L = 5m A = 300 mm² E = 200 GPa 2 m 1.5 m dc ! P =92 KN 2 m D final position
A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B, C, and D. If the tension in wire AB is 840N, determine the vertical force P exerted by the tower on the pin at A.
2 ft -2 ft 2 ft A 90 65 200 lb 100 lb 2. A beam AB is loaded as shown. The beam is pin-connected to the wall at A. At Ba 10-inch diameter pulley is attached through frictionless bearing to the beam. A rope passes around the pulley and is connected to C and D vertically above the extremities of the horizontal diameter of the pulley. Determine the pin reaction at A and the tension in the rope. Hint: Pin connection has vertical and hozirontal reactions.
3. Three cables are joined at the junction ring C. Determine the tensions in cables AC and BC caused by the weight of the 30-kg cylinder. A 45° 30% B 15⁰ 30 kg
A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B, C, and D. If the tension in wire AB is 630 lb, determine the vertical force P exerted by the tower on the pin at A.
3. A load of 150 kN is acting at A on the machine part shown. 150 kN 40 mm Bo 40 mm C a.) When the applied load of 150 kN is replaced by an equivalent force-couple system with the force acting at point B, Determine the magnitude of the couple. b.) When the applied load of 150 kN is replaced by two horizontal forces, one acting at point B and the other acting at point C, determine the magnitude of the force at B. 80 mm 80 mm
4 m 4 m| 4 m 4m| 4 m| 4m K. J. LM IN 6 m A design model for a transmission-line tower is shown in the figure. Members GH, FG, OP, and NO are insulated cables; all other members are steel bars. For the loading shown, compute the forces in members IF and DS. Indicate the nature of the force H 60° P 30 60 30 6 m D R 25 kN 25 kN 6 m C. 6 m B T 6 m A U 5.4 m
Consider the simply-supported overhang beam shown. There is a pin support at A, a roller support at D, and an overhang of 2m. If the pin at A is 10mm in diameter, calculate the shear stress on the pin assuming double shear connection. 5kN/m 2kN/m B C 3m 2m- 1m -2m 2m-
5. A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B, C, and D. If the tension in wire AB is 110 lb. (a) Determine the vertical force P exerted by the tower on the pin at A. (b) Determine the moment about point 0 of the Resultant Force. 25 ft 20 ft 100 ft B 60 ft 20 ft 18 ft 74 ft
If the beam shown is supported by the fixed wall at B and the rod AC. if the rod has a cross sectional area = 7 x104 m² and is made of the same material of the beam if the area moment of inertia of the beam's cross section is 2.8 x 10-6 m4 if the distributed load w = 8 kN, then, the tension in the rod AC is T. 1m 1 m 2 m O a. 6.00 O b. 873.69 Oc. 59910.13 O d. 26.00