a) AK type thermocouple is utilized in the figure given below. The reference temperature (cokd junction) is Te 27.35 C and the thermocouple EMF output (comparative with the cold junction) is Vout = 1.549 mv. What is the temperature of the Active thermocouple (Hot Junction)? SV Active Thermocouple LM 335 OP Inactive Themocouple

a) AK type thermocouple is utilized in the figure given below. The reference temperature (cokd junction) is Te 27.35 C and the thermocouple EMF output (comparative with the cold junction) is Vout = 1.549 mv. What is the temperature of the Active thermocouple (Hot Junction)? SV Active Thermocouple LM 335 OP Inactive Themocouple

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The positive peak value of output waveform for the given circuit diagram is.. (VPP of input is 18 V, Bias voltage is 3 V, Diode is germanium) R: D, VIN VouUT VaAS
Design the power supply using diode components. This power supply sholud have 2 outputs. 12Vdc and 5Vdc. Input 240 Vac Supply i. Draw the circuit diagram ii. Bill of material/components that will be used iii. Teh output waveform for each stage
The arrow on the symbol of MOSFET indicates O a. that it is a N-channel MOSFET O b. the direction of conventional current flow O c. that it is a P-channel MOSFET O d. the direction of electrons
1. A six-pulse uncontrolled recti load. The inductance is very 1 (a) Determine average load o (b) Determine the maximum (c) Determine the maximum (d) Determine average loac (e) Carefully sketch the wav diode conduction pattern.
4. Draw and explain the circuit of a simple AM demodulator using Junction diode ( draw the input and output waveforms )
c) Using a Si diode, design a clamper circuit that will result in the desired output waveform as shown in Figure Q2c. Show overall analysis to justify the proposed design. Vi Vo 20 Designed Clamper Circuit - 3 V -20 - 43 V- Figure Q2c
A 10 V Zener diode is used to regulate the voltage across a variable loadresistor. The input voltage Vs varies between 13 and16 V. The loadcurrent (??) varies between 10 and 85 mA. The minimum Zener current is15 mA. Findi. The maximum value of Rsii. The maximum power dissipated by the Zener diode, using the value ofRs.
The operating point is also called the . ..... ..... .. Select one: a. Cut off point b. Saturation point c. Quiescent point d. None of the above
Figure shows a composite switch consisting of a power transistor (BJT) in series with a diode. Assuming that the transistor switch and the diode are ideal, the I-V characteristic of the composite switch is
The positive peak value of output waveform for the given circuit diagram is. Bias voltage is 2 V, Diode is germanium) (VPP of input is 18 V, V VouT
1. A voltage regulator with a no-load output dc voltage of 12 V is connected to a load with a resistance of 10 ohms. If the load resistance decreases to 7.5 ohms, the load voltage will decrease to 10.9 V. What is the percent load regulation, and calculate the load current. Determine the amount of anode voltage needed to turn on the PUT in the circuit as shown. Also determine oscillating frequency. Vy = 0.8 V, ly = 15 mA, lp = 36 uA. 2. 1₁ R₁ • 470 ΚΩ +18 V AO 0.22 μF WI VG = +9 V G -ok R4 • 22 Ω R₂ • 10 ΚΩ +1₁ R3 10 ΚΩ
b.for Bridge fullwave rectifier ,draw circuit diagrm and find Vde, Vrms & Vripp when Vin-30oVac.