A moment about the z-axis of 192 N-m is applied to a beam with dimensions b = 85 mm and h = 302 mm. If there are no other loads applied to the beam (My, P, Vy and Vz = 0), what is the normal stress at point F? Give your answer in kPa to two decimal places with negative indicating compression and positive indicating tension. b/4

A moment about the z-axis of 192 N-m is applied to a beam with dimensions b = 85 mm and h = 302 mm. If there are no other loads applied to the beam (My, P, Vy and Vz = 0), what is the normal stress at point F? Give your answer in kPa to two decimal places with negative indicating compression and positive indicating tension. b/4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Below Figure shows the section of an angle purlin. A bending moment of 60 5 kN.m is applied to the purlin in a plane at an angle of 30 deg to the vertical y axis. If the sense of the bending moment is such that both its components Mx and My produce tension in the positive xy quadrant, calculate the maximum direct stress in the purlin, stating clearly the point at which it acts. * 100 mm BỊ 10mm 30° C ID 10mm 57 MPa. 89 MPa. Non Above 72 MPa. 125mm
A standard truck moves across a 25- meter span. The wheel loads are P1=36 kN and P2=142 kN separated by 4.3 m and P3=142 kN at 7.6 m from P2. Determine the beam dimensions if the maximum flexural stress is equal to 100 MPa. Use the ratio h = 1.6b. Round your answer into the nearest whole number. O 213 mm x 415 mm O 415 mm x 213 mm O 321 mm x 514 mm O 514 mm x 312 mm
with the following modifications: Add an additional force P = 20kN acting downwards at point B
A folding tray mechanism is attached to a wall as shown. Find the internal forces and bending moment in the lower support arm at section s-s, located midway between points B and E, when a force of F = 270 N is applied at an angle of 0 = 28°. 2013 Michael Swanbom Ⓒ030 BY NC SA k s -Ś a b G с h₁ h₂ ка E S- B Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 16 cm 19 cm 25 cm 23 cm 17 cm The internal axial load at section s-s is A = The internal shear load at section s-s is V = The internal bending moment at section s-s is M = N. N. C. N-m. 0
Use the method of SECTIONS to find the true magnitude and direction in bar HG of the truss shown below in Fig 3.5 -500lb -100lb A 45° -200lb H -100lb 2 B -200lb -200lb MAGNITUDE AND DIRECTION OF SUPPORTS -500lb H -100lb 45° 2¹ C2D 2¹ Fig 3.5. -200lb -100lb LI 2 B 2₁ 2₁ D 2₁ E
11:11 A The wood beam has an allowable shear stress of Tallow = 9.6 MPa. d3 d3 Variable d₁ d₂ d1 d3 d4 d5 wamap.org Value d2 V Values for the figure are given in the following table. Note the figure may not be to scale. 0.05 m 0.125 m 0.05 m 0.225 m P 0.1125 m d1 d5 a. Determine the Q at point P. b. Determine the moment of inertia, I. d4 c. Determine the magnitude of the max shear force that can be applied to the cross-section at point P, Vmax.
What are the magnitude (F) and the location measured from end A (d) of the equivalent resultant force of the triangular distributed load in the figure below 3m в Select one O a F 9 KN: de 6 m O b F 18 KN: d 6 m O c F6 KN: d= 6.5 m O d. F-6 KN:d1m
Given the beam and the external loading shown below, if L = 15 m, w1 = 510 N/m and w2 = 1,600 N/m, calculate: • the magnitude and location of the equivalent resultant force (a single equivalent force, for the whole loading block, NOT two equivalent forces from dividing into rectangular and triangular stress blocks). • the reactions at the beam supports. W2 w, A L Resultant force Fr = 单位 (tolerance 1 N, magnitude only) Location xbar = 单位 (tolerance 0.1 m, measured from A) Reactions: Ay = 数字单位 (tolerance 1 N, observe up positive sign convention) MA= 数字单位 (tolerance 10 N*m, observe anti-clockwise positive sign convention)
The state of stress at a point in a machine component is given by ox = 120 MPa, oy = 55 MPa, Oz = -85 MPa, Oxy = -55 MPa, Oxz = -75 MPa, and oyz = 33 MPa. Construct the Mohr's circles of stress for this stress state and find the maximum shear stress.
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section
For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. V = 7 kN, V2 = 7 kN, V3 = 100 mm, and V4 = 1300 mm. (mm) 0 Provide values at all key points shown the given shear-force and bending-moment diagrams. X (mm) A C V2 B E D F 0.00 +V Reaction force R₁ (left) = In the shear-force and bending-moment diagrams given, 0.00 X (mm) kN and reaction force R₂ (right) = P KN. 0.00
The cross-sectional area shown is subjected to V = 600 kN and M =1000 kN-m. What is the transverse shear stress just above point B? (in MPa) 100 mm 100 mm 100 mm 100 mm 100 mm B 100 mm A V