A rectangular, tension-reinforced beam is to be designed for dead load of 500 lb/ft plus self- weight and service live load of 1200 lb/ft, with a 22 ft simple span. Material strengths will be fy = 60 ksi for and fc' = 3 ksi for steel and concrete, respectively. The total beam depth must not exceed 16 in. Calculate the required beam width and tensile steel requirement, using a reinforcement ratio of 0.600.005- Use ACI load factors and strength reduction factors. The effective depth may be assumed to be 2.5 in less than the total depth.

A rectangular, tension-reinforced beam is to be designed for dead load of 500 lb/ft plus self- weight and service live load of 1200 lb/ft, with a 22 ft simple span. Material strengths will be fy = 60 ksi for and fc' = 3 ksi for steel and concrete, respectively. The total beam depth must not exceed 16 in. Calculate the required beam width and tensile steel requirement, using a reinforcement ratio of 0.600.005- Use ACI load factors and strength reduction factors. The effective depth may be assumed to be 2.5 in less than the total depth.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. An interior reinforced concrete slab has to be designed to support a live load and a dead load in addition to its own weight based on the following specifications: The slab is one-way and simply supported with a span of 12 ft. The live load on the slab is 200 psf. The dead load on the slab is 100 psf. Your design will use concrete compressive strength fe= 3000 psi and steel yield strength of fy = 40,000 psi
A rectangular beam has the dimensions (see Figure) b = 12 in., h - 20 in, and d 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in. The concrete compressive strength fe is 4000 psi, and the tensile strength In bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the concrete compression stress at the top fiber caused by a bending moment M- 10 ft-kips. 9- 6.78 in, I= 4067 in, Es= 29000000, E = 3600000 17 in. 20 in. 3 #9 bars (A, - 3.00 in.?) 3 in. -12 in- Select one: a. 390 psi b. 1390 psi c. 200 psi d. 250 psi
FLEXURAL ANALYSIS CONCRETE UNCRACKED Problem: Calculate the uniform load (in addition to the beam weight) which will cause the section to begin to crack if they are used for 28 ft simple span. = 4000 psi , the modulus of rupture f, = 7.5f',, and reinforced concrete weight is 150 lb/ft³. 15" 18" 2 #8 3" 12"-
Problem Solving: A rectangular beam has dimensions of 250 mm by 625 mm with an effective depth (distance from extreme fiber in tension to the centroid of the reinforcing bars) of 575 mm and is reinforced with three 25 mmp. The concrete cylinder strength f.' = 27.6 MPa and the tensile strength in bending (modulus of rupture) is 3.28 MPa. The yield point of the steel is 414.7 MPa. The beam carries a bending moment of 61 kN.m. E_ = 200000 MPa. E_ = 4700,f. Using the transformed area method, determine the stress in the extreme fiber in compression.
a t-beam has the following properties; bf = 820mm, bw = 250mm, d = 470mm and tf = 100mm. Concrete compressive strength is 20.70 MPa and the steel yield strength is 414 MPa. Determine the number of bars need if MDL = 150 kN-m and MLL = 120 kN-m. Use 25 mm bar. What is the steel area needed?
A RC beam of cross section 220 × 460 mm is subjected to following forces: Factored shear force = 30 kN Factored bending moment = 35 kNm Factored torsional moment = 5 kNm What should be the minimum area of tension steel provided such that there is no need to provide torsional reinforcement. Use M20 grade concrete and Fe415 grade steel. Use the following data for M20 grade concrete. 100 As 0.50 0.75 1.00 1.25 1.50 bd Design shear stress (N/mm²) 0.48 0.56 0.62 0.67 0.72
2. Determine if the composite beam pictured below is adequate for this application (this includes bending, shear, deflection and shear stud limit states). The dead load for this beam is 10 psf plus the weight of the deck, which is made from normal weight concrete. I 5" 5" Normal weight slab fc=4000 psi W24x94 Span length = 30' Service Live Load = 100 psf 3/4" Diameter Shear Connectors 8' o.c. typical Fu=60 ksi (shear connectors)
Design the simply supported beam shown in the Figure 1 for flexure Consider the following data. Characteristic compressive strength of concrete, fck= 25 N/mm? %3D Characteristic tensile strength of steel, fyk = 500 N/mm? Effective cover to reinforcement is 30 mm Density of Block work = 20 kN/m3 Draw the cross section of the beam at the mid span Height of 200 mm thick wall above the beam is 4 m 200 mm - Imposed Load-20kN/m 600 mm - 6 m
Situation 3: A6 m long fix-ended concrete beam has a width of 310 mm and an overall depth of 480 mm. The beam is reinforced with 4-28 mm diameter bars at the bottom and 2-28 mm bars on top. Steel cover measure from the center of the bar is 70 mm. f'e- 28 Mpa and fy-415 Mpa. Total dead load including beam weight is 22 kN/m. Assuming the analysis is Doubly-reinforced beam. 7. Determine the depth of compression block in mm. 8. Determine design ultimate moment of the section if reduction factor is 0.90. 9. Determine the additional concentrated live load can carry at the midspan.
300 mm 2012 3614 250 mm Check the requirements of TS500 for ductile design and Determine the Moment resisting capacity, Mr, of doubly reinforced section. Material: C30/B420C Concrete cover=25 mm
Problem 1: A singly reinforced rectangular beam has a dimension b = 310mm and d = 410 mm. Factored moment is equal to 300 kN-m, Concrete compressive strength is 24 MPa, Steel yield strength is 276 MPa and the reduction factor is 0.9. Determine the required steel area in mm². Show the graph.
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPa. a) Maximum Steel ratiob) Tension Forcec) Compression Force