A singly reinforced rectangular beam section 250 mm wide, 450 mm deep is reinforced with 2-28-mm-dia. rebars, grade G420 enclosed with 10-mm-dia. stirrups. What is the design condition of the beam by USD method? Use f'c = 21 MPa A. Transition Failure B. Balance Strain Failure C. Compression Controlled D. Tension Controlled

A singly reinforced rectangular beam section 250 mm wide, 450 mm deep is reinforced with 2-28-mm-dia. rebars, grade G420 enclosed with 10-mm-dia. stirrups. What is the design condition of the beam by USD method? Use f'c = 21 MPa A. Transition Failure B. Balance Strain Failure C. Compression Controlled D. Tension Controlled

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with d-20-mm-dismeter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is M0 mm and at the bottom is 70 mm. Use concrete strength r'e-21 MPa und steel yield strength fy 415 MPa for 20- mm bars and fy= 275 MPA for 16 mm bars Detenmine the design moment capacity n kN m of the beam in negative bending. A 40.06 O45.07 C. 42.70 D47.55
USE NSCP 2010 A simply supported beam is reinforced with 4 – 28 mm ø at the bottomand 2 – 28 mm ø at the top of the beam. Steel covering to centroid ofreinforcement is 70 mm at the top and bottom of the beam. The beamhas a total depth of 400 mm and a widthof 300 mm. fc’ = 30 MPa, fy = 415 MPa. Balanced steel ratio ρb = 0.031.Compute the ultimate moment capacity of the beam in kN-m. Usereduction factor of 0.90
A beam cast monolithically has the following properties: bf=1200mm, t or hf = 110mm, bw=380mm and h=800mm. It is reinforced with 10D32mm grade 420MPa bars. Concrete strength is assumed to be 27.5MPa and the centroid of tension reinforcement is located 665mm from the outermost compression fiber. A. Determine maximum nominal moment to ensure tension controlled, kN-m. B. Calculate the balanced steel area, mm2. C. Calculate the balanced moment in kN-m.
Details of a rectangular column are as follows: Column width along X-axis-250 mm Column Depth along the Y-axis-600 mm 8-25 mm diameter bars distributed equally along the longer sides. 10 mm diameter ties spaced at 10 mm on centers Concrete 28th day Compressive strength, fc;=20.7 MPa Reinforcing Steel yield strength, fy-415 MPa Assume that compression steel yields. a) Which of the following gives the nominal balanced load Pb (kN). A = 90.4 mm b) Which of the following gives the nominal axial load (kN) that the column n carry at an eccentricity of 200 mm along the X axis from the centroidal Y-axis.
A beam has a width of 300 mm and an effective depth of 480 mm strength Pc= 34 MPa. Steel yield strength fy=415 MPa. The section is to be reinforced for tension only and the effective concrete cover is 70 mm. Deadload moment is 140 kN-m and the liveload moment is 180 kN-m. Use 2010 NSCP with t= 0.005. A. What is the governing steel ratio? B. What is the maximum number of bars needed for a 25mm diameter reinforcements? C. What is the minimum number of bars needed for a 25mm diameter reinforcements?
3. A reinforced rectangular concrete beam having a width of 300 mm, effective depth of500 mm, fc’ = 24 MPa, fy = 415 MPa, 4 - 28 mmɸ, d’ = 65 mm. Present the following (a) actual steel ratio (b) maximum steel ratio (c) a(d) c (e) check if steel yields (f) ?steel(g) type of failure (h) reduction factor (i) moment capacity
The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec =23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f' = 25MPa 800 IDE 730 N12 ligs (fsv.f-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Calculate the combination load for the reinforcement concrete beam shown in Figure 3. Unit: KN/m with two decimal. 1.2G+1.5Q=w
1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Notes:• All dimensions are in millimeters.• Column reinforcement not shown for clarity• Column and beam are neither exposed to weather nor contact with the ground.• Analyze as singly reinforce beam only.• Neglect the weight of the beam.• Concrete isnormal weight and reinforcements are galvanized. d. What is the flexural capacity of the beam at face of support in kNm? e. What is theshear capacity of the beam at face of support in kN? f. What is the maximum Pu (kN) that can be applied at the free end of the beam consideringflexure and shear? g. What is the requiredminimum cut length (mm) of each stirrup? Roundyour answer to nearest safe25 mm.
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f^c=28 MPa fy = 276MPa Aps = 800 mm² Ds = 10mm Dm = 18mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250kN
The details of the cantilever beam are shown below. Use f’c = 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Notes:• All dimensions are in millimeters.• Column reinforcement not shown for clarity• Column and beam are neither exposed to weather nor contact with the ground.• Analyze as singly reinforce beam only.• Neglect the weight of the beam.• Concrete is normal weight and reinforcements are galvanized. What is the flexural capacity of the beam at face of support in kNm? What is the shear capacity of the beam at face of support in kN? What is the maximum Pu (kN) that can be applied at the free end of the beam considering flexure and shear? What is the required minimum cut length (mm) of each stirrup? Round your answer to nearest safe25 mm
An existing T-beam section was investigated and found out the following elements: Top bar reinforcement: 1500 mm2 Bot bar reinforcement: 2500 mm2 thickness of slab = 100mm effective depth from the surface of the slab = 450mm effective width of flange = 1000mm Top bar concrete cover at center of the bar = 50mm fy = 414Mpa f'c = 28Mpa use f’y = fy Determine the depth of compression block in mm, in 3 decimal places.