An L-shaped bracket is fastened to the wall (x-z plane) at points A and B and extends out parallel with the y-axis to point C. A 200 N force is applied at point C in the x-z plane at the angles shown. Solve for the moment of force created at point A by the 200 N force. Express the moment as a vector in cartesian form (2 JWT

An L-shaped bracket is fastened to the wall (x-z plane) at points A and B and extends out parallel with the y-axis to point C. A 200 N force is applied at point C in the x-z plane at the angles shown. Solve for the moment of force created at point A by the 200 N force. Express the moment as a vector in cartesian form (2 JWT

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A force F= 338 N is applied as shown to the bracket ABC. a=134 mm; b=54 mm; c=90 mm; B=33 in degree. F a IB b 4a) Determine the y component of the moment of the force F about point A in Nm.
Below is a truss created with 3 rod elements. Fixed at point A, sliding support at point Chas. At point B, the load P acts on the system as shown. All 3 elements have the same cross-section and are rectangular.section dimensions are given in the figure. If the safety factor used in the design is 2.5, the buckling stability should be taken into account.Calculate the highest value of the load P. E = 20 GPa
the truss carries forces shown in the figure. determine the resultant of the forces and its intersection with AB measured from A.
The truss shown in the figure is applied with force P = 5kN.Determine the force in member DE,BC, AND DB.
A frame and loading are shown. B 90 mm D 120 mm ' 120 mm' 120 mm Determine the force acting on member ABCat C. Take P= 420 N. The force acting on member ABC at Cis N.
Find the force in truss DE. T = 390 N, x = 1.8 m. (Note: if the force in the truss is in tension, please enter a positive value; if it is in compression, please enter a negative value.) A F
The 500-N force F is applied to the vertical pole as shown. Determine the scalar x-component of the force vector F along the x’- and y'-axes. Determine the scalar x-component of the force vector F along the x- and y’-axes Determine the scalar y-component of the force vector F along the x'- and y’-axes. Write F in terms of the unit vectors i and j.
A container of weight W is suspended from ring A. Cable BAC passes through the ring and is attached to fixed supports at B and C. Two forces P = Pi and Q = Qk are applied to the ring to maintain the container in the position shown. Knowing that W=270 lbf, determine: - (a) The magnitudes (not vectors) P and Q. (b) The vectors P and Q canonically (cartesian vector notation) Hint: The tension is the same in both portions of cable BAC. yI 16 in. Z B A 10 W 48 in. P 72 in. 13 in. X 24 in.
For the following indeterminate truss (with SI = 1) determine all the member forces using the Force method. E is constant for all members. A for all members is shown in the figure. Solve by taking the axial force NBC as the redundant. 40 kN ● pin roller 600 mm² 1.2 m 600 mm² 600 mm² 1200 mm² 600 mm² 1200 mm² B 0.9 m 30 kN
(2.) The following beam is subjected to bending. Consider cross-section K! a + + 쇼 K F + 1/2 + 1/2 + y- + A O e B + a + F = 15 kN 1 = 2.4 m a = 80 mm v = 5 mm a) Calculate the normal stresses at the marked vertices (A and B) of cross-section K, if the following geometric data of the section are given: principal moments of inertia and position of the centroid of the shape. e = 2.230 cm; I₁ = 77.650 cm¹; 1₂ = 18.178 cm*
Solve the problem with complete and neat solution. Draw the figure. Determine the force in each member of the bridge truss shown. State whether each member is in tension or compression. 100KN K 3m 3m B
Determine the force in each bar of the truss shown in the figure in teerms of P.