An open cylinder of air has a radius of 38.0 cm and a height of 50.0 cm, as shown in figure (a). BOK b 50.0 cm mm Ah The air pressure is 1.00 atm and the temperature is 13.5°C. A 25.0 kg piston is then lowered onto the cylinder, forming an airtight seal, as shown in figure (b). The air inside is compressed until the piston reaches equilibrium (mechanical and thermal), and at this point the piston is a height h; from the bottom of the cylinder. Lastly, a 27.5 kg dog steps onto the piston, and the air in the cylinder again compresses, as show in figure (c). After reaching equilibrium, the air inside is again at 13.5°C, and the height of the piston decreases a distance Ah as shown. (a) What is the distance Ah (in mm) that the piston moves when the dog is on it? C °℃ (b) To what temperature (in °C) should the gas be warmed to raise the piston and the dog back to h;?

An open cylinder of air has a radius of 38.0 cm and a height of 50.0 cm, as shown in figure (a). BOK b 50.0 cm mm Ah The air pressure is 1.00 atm and the temperature is 13.5°C. A 25.0 kg piston is then lowered onto the cylinder, forming an airtight seal, as shown in figure (b). The air inside is compressed until the piston reaches equilibrium (mechanical and thermal), and at this point the piston is a height h; from the bottom of the cylinder. Lastly, a 27.5 kg dog steps onto the piston, and the air in the cylinder again compresses, as show in figure (c). After reaching equilibrium, the air inside is again at 13.5°C, and the height of the piston decreases a distance Ah as shown. (a) What is the distance Ah (in mm) that the piston moves when the dog is on it? C °℃ (b) To what temperature (in °C) should the gas be warmed to raise the piston and the dog back to h;?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylinder of 0.9 m3 in volume contains air at 0℃ and 39.24 N/cm2 absolute pressure. The air is then compressed to 0.45 m3. Find: a. The pressure inside the cylinder assuming isothermal process b. The pressure and temperature assuming adiabatic process. Take k = 1.40
6. There is air in the cylinder with the piston. The cross-sectional area of the piston is 5cm, the initial volume is 30cm, the pressure is 1 bar, and the temperature is 20℃. As shown in the picture next, the spring constant of the connected spring is ks=100 N/cm, and it is not deformed initially. By applying heat, the cylinder expands and the pressure in the cylinder becomes 4 bar. Answer the following questions. (hint: The relationship between P and V is straight) (1) Find the final volume (expressed in cm^3). (2) Find the expansion work during this process. (3) Find the amount of heat transfer during this process. Show this process on the P-v diagram
A dormitory room measures 4m x 6m x 6m. A student turns on a 150 watts fan before leaving the room on a summer day, hoping that the room will be cooler when she returns in the evening. Assume that all doors and windows are tightly closed, and there is no heat transfer through the walls and windows. At the start of the day, the room temperature is 15°C, and the pressure is 100 kPa. What will be the temperature inside the room when the student returns 10 hours later, given the specific heat value of air at room temperature?
Determined the change in internal energy if there are 2kg of gas inside a rigid container, for which R=240J/kg-K (k=1.50), initial pressure P1= 500.16kPa and temperature and T1 = 70C, then pressure increase to 1675kPa.
The cylinder, which has a sensitively moving piston inside, is filled with V₁ = 0.93421 The temperature outside is T₁ = 8 °C and the air pressure is p₁ = 101 kPa The piston is quickly pressed into the cylinder, causing the volume in the cylinder to decrease to V3 = 0.2975 1 and the pressure to increase to p2 = 210 kPa. The piston is locked in place and the cylinder is immediately brought to the laboratory. After that, it happened that the gas temperature became same as the laboratory temperature of T3 = 22 °C Determine the gas pressure when the gas temperature has reached the final temperature of the laboratory. What is the algebraic expression for pressure in terms of V_1, T_1, p_1, V_3 and T_3 P3 = What is the pressure? P3 = kPa
For a gas of volumes Vi = 9.50 10-4 m3 and Vf = 1.40 10-4 m3 and pressures Pi = 2.00 106 Pa and Pf = 2.05 107 Pa, answer the following.For an isobaric process at Pi, find the internal energy change of the gas during this process.For an isovolumetric process at Vi, find the internal energy change of the gas during this process.
In the figure below, the tank contains water and immiscible oil at 20°C. What is h in cm if ha= 18cm, h=14cm, hc= 12cm, and the density of the oil is 898 kg/m³? Assume the density of water to be equal to 998 kg/m³. h = h ha hb cm. Oil hc Water
Consider the figure below where a cylinder of an ideal gas is closed by an 12 kg movable piston of area = 70 cm?. When the gas is heated from 30 °C to 100 °c the piston rises by 20 cm. The piston is then fastened in place and the gas is cooled back to its original temperature of 30 °C. Find the difference in heat between the heating process (AQ1) and the cooling proecess (AQ2 ); AQ1 -AQ2. Piston Gas
Water is enclosed in the piston/cylinder system as shown in the figure. The initial temperature of the water is T1 = 140 °C. The mass of the enclosed water is m, = 12 kg. The piston has mass, m, = 500 kg and diameter, D, = 0.125 m. The water is heated until the specific volume is v, = 0.05 m/kg at which point the piston is fixed in position by a pin, i.e. piston can no longer move. The water is then further heated to a final temperature of T3 = 350°C. Assume that the atmospheric pressure is Po = 100.3 kPa and gravity is g = 9.81 m/s. a) What is the initial pressure of the water, P1, and specific volume v:? b) At state 2 what is the temperature, T2, and is the water a compressed liquid, saturated mixture or a superheated vapour? If the state is a saturated mixture, determine the quality. c) What is the final pressure of the water, P3? d) Draw a P - V (pressure - volume) diagram of the process. Label all state points, process lines, constant temperature line(s) and the pressure and…
THERMODYNAMICS SUBJECT NEED ASAP Two spherical vessels of different sizes contain the same gas and are connected by means of a pipe with a valve. Sphere A has a diameter of 5 foot at the given pressure gauge of 50 kgf/cm². Sphere B contains the same gas at 20 kgf/cm² gauge. The valve is opened and when the properties have been determined, it is found out that the gauge pressure is 36 kgf/cm². The temperature at the two vessels before and after opening the valve is maintained at 21.1°C. If the barometric pressure is 750 torr and the gas inside the sphere is nitrogen, find the following: The atmospheric pressure in psi The diameter of Sphere B The total mass of the gas after opening the valve I hope you can all answer this question I know tutor can answer until 4 parts. Thank you will give thumbs up
Thermodynamics The gas is compressed in a piston and cylinder arrangement. Diameter of the piston is 20 cm. Force acting on the gas is 20 kN. Determine the gauge pressure in kPa. Assume atmospheric pressure is 1 atm pressure.
A cylindrical vessel with a diameter of 8 inches and 5 feet long contained acetylene at 300 psi gauge and 82°F. After some amount of acetylene was used, the pressure was reduced to 190 psi gauge and the temperature was 74°F. The gas constant of acetylene is 59.35 ft-lb:/lbm-°R. Determine the following: 1. What is the initial mass in Ibm of the acetylene inside the vessel? 2. What proportion in percentage of acetylene was used? 3. What volume in ft would the used acetylene occupy at 30 psig and 80°F?