Assume that each diode in the circuit shown in Figure 3 has a voltage of Vp=0.65V. (a) The input voltage is V₁ = 5V. Determine the value of R₁ required so that ID is half the value of ID2- Which are the values of ID: and ID₂? (b) If V₁ = SV and R₁ = 2k2, determine ID: and ID₂ R₁ Fig 3 ID2 R₂ 1kΩ : IDI Vo

Assume that each diode in the circuit shown in Figure 3 has a voltage of Vp=0.65V. (a) The input voltage is V₁ = 5V. Determine the value of R₁ required so that ID is half the value of ID2- Which are the values of ID: and ID₂? (b) If V₁ = SV and R₁ = 2k2, determine ID: and ID₂ R₁ Fig 3 ID2 R₂ 1kΩ : IDI Vo

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
Given the following circuit with VDD= 9.2 V, R=2.3 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. I VDD a. 0.004000 A O b. 3.717391 A OC. 0 A d. 4.000000 A e. 0.003717 A R + VD -
For the circuit below, assume the diodes operate with a constant voltage drop of .7V, find Vx, Vy, VD4 and ID2. 15V 15V Allt V1 V2 R1 1k IDC 1mA Vx R2 2k ww D1N4002 Vy D1N4002 7D1 D1N4002 D2 D3 R3 1k D4 D1N4002
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
Assuming an ideal diode model for all the diodes in the circuit below, Calculate the voltage across and current flow through each diode R1 D2 9kQ 1N1199C R2 D1 18k0 1N1199C V2 12 V R3 1kQ D3 1N1199C R4 5k0
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms
5. Assume each diode in the circuit has a cut in voltage of 0.65V. The input voltage is Vi = 5V. Determine the value of R1 required such that ID1 is one half of ID2. What are the values of ID1 and ID2? R1 VD VD1 Vo VD2 V1 5V R2 1kQ ID1 ID2 3. (a die
Draw the corresponding output waveform of the double diode partial limiter below using simplified diode model. Indicate all the necessary voltage levels and use Silicon diodes. 20 VP-P 1KQ M D1 9V D2 4.5V VOUT
Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state (bias) for each diode. R1 ww 9kQ 1N1199C R2 D1 18kQ 1N1199C V2 12 V R3 1kQ D3 1N1199C R4 D3: On (Forward Bais) D3: Off (Reverse Bais)
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
120 V rms elile a. DI D2 # What is the peak current through each diode? b. What is the P/V for each diode? (Ctrl) - 5ΚΩ