At the instant shown in Figure 1, determine by Graphical Method: a) Velocity and Acceleration of point 'B' b) Velocity and Acceleration of point 'D' C) Angular Acceleration of Link 6 (DO6) Note: Your working must be hand drawn O6 0,4 = 51 mm AB = 102 mm AC = 203 mm BD = 102 mm 3. O,D= 102 mm 3 45° 0,0, = 102 mm a, =1 rad/s 1.

At the instant shown in Figure 1, determine by Graphical Method: a) Velocity and Acceleration of point 'B' b) Velocity and Acceleration of point 'D' C) Angular Acceleration of Link 6 (DO6) Note: Your working must be hand drawn O6 0,4 = 51 mm AB = 102 mm AC = 203 mm BD = 102 mm 3. O,D= 102 mm 3 45° 0,0, = 102 mm a, =1 rad/s 1.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

B3. SOLVE STEP BY STEP IN DIGITAL FORMAT A set of sprockets is constructed, as shown in Figure 1, so that the second and third rotate on a common axis. When the first rotates, it drives the second and this in turn drives the third. Let and be the numbers of revolutions per minute of the first, second, and third axes. dy du dy dy dtu Find www.du' dx' and, and verify that dr du Figure 1 |1cm axis 1 |- 4cm -| axis 2 axis 1: y rev per minute axis 2: u rev per minute axis 3: x rev per minute |1e| |- 3cm-|| axis 3
(10 points) Crank_Slider2 a WOP, dop Known values: a 0.38 m 3.4 m 20° 68° Problem Statement: Crank OP rotates about fixed axis O, causing slider Q to oscillate in a horizontal track. At the instant depicted, the angular velocity of crank OP is 4 rad/s and its angular acceleration is 6 rad/s?. For that instant, determine the following. The velocity vector of pin P: i+ 1.4283 m/s -0.5199 m/s The angular velocity of rod PQ: The velocity vector of slider Q: The acceleration vector of pin P: 计 The angular acceleration of rod PQ: The acceleration vector of slider Q: i+
Answer using GRAPHICAL METHOD. Make a representation of the following vector quantities a. A velocity of 20m/s north b. A force of 2000 dynes 45° east of south c. An acceleration of 5m/s2 at 200° d. A displacement of 14m 100° from +x-axis e. A force of 250N at 60° clockwise +x-axis
V-axis X-axis A Figure 1. An object (yellow point) travels from point A to point B along the arc of a circle that is centered at point O (red point). velocity of an object, either due to a change in speed or direction, means the object is accelerating. According to Newton's second law, an object will accelerate only if there is a non-zero total force acting on the object. For uniform circular motion, it turns out that this force must always be pointing towards the center of the circle that the object is travelling around and we say that there is a centripetal force present. You can use Newton's second law and a little bit of geometry to understand why an object undergoing uniform circular motion must be experiencing a force that is pointing towards the center of the circle the object is travelling on. If the acceleration vector pointed above or below the plane of the circle, the velocity vector would also end up pointing out of the plane that the circle is on. Since the velocity vector…
Q2: Write the G-code for the below geometry, use G90, explain all code steps. 30 30 40 R40 R30 DATUM 70 30 Start Point
Consider the figure as shown below. O-XoYoZo is the reference frame and O-X₁Y₁Z₁ is the frame attached to the tool. Sketch the tool position after each intermediate position of the operation of the tool about the reference frame: roll π/2(rotate about Zo), pitch -T/2(rotate about Yo), yaw π/2(rotate about Xo). Please write the final rotation matrix expression. ZI,Zo XI,Xo Yı, Yo
Write a CNC Milling program to machine the outer profile of a 6 mm thick aluminum sheet. Cutting parameters: depth of cut 3 mm, speed 1200 rpm, feed rate 100 mm/min, and coolant. Tool size 8 mm. (you can use the tool cutter compensations codes). Use an absolute coordinate from the point identified as tool position. 10 40 R 10 R 10 40 Tool position 20 z, 10 mm above All units in mm the sheet
The figure below represents a Whitworth quick-return mechanism which is used in shapers. It is required that the tool holder (link 6) maintain a nearly constant velocity during the cutting stroke but accelerates on the return stroke in order to reduce idle time. The inputs are: VA2=8m/s, a2=0. Find the following: a) The angular velocity m4 b) The magnitude of the sliding velocity and acceleration of A c) Angular acceleration a4 d) Find the acceleration of A via link 2 e) Find the acceleration of A using the angular velocity and acceleration along with the Coriolis effect and the acceleration along the axis of slip (via link 4) f) Find the acceleration of the tool holder (C). 2 (VA2 = 6 m/sec 02 4 B * 45° 0,04 0,A = 19.1 cm 0,B = 10.2 cm 35.6 cm 8.9 cm 04 BC
Find the velocity of point B and angular velocity in link 3 using relative analysis and polygon method. Note the drawing is not in scale. B 02 @2=1 rad/s 2 30° A 1 3 4 04 02A=4" AB=7" 0204-=9" 04B=8"
Refer to the figure below for the mechanism.If link 2 rotates at a speed of 60 revolutions per minute, find the velocity, using resolution and composition method of: A point connecting link 2 to link 3 A point at the center of link 2 A point at the center of link 3 Of the slider Also, locate all the instantaneous centers. Use counterclockwise direction.
Refer to the figure below for the mechanism. If link 2 rotates at a speed of 60 revolutions per minute, find the velocity, using resolution and composition method of: A point connecting link 2 to link 3 A point at the center of link 2 A point at the center of link 3 Of the slider Also, locate all the instantaneous centers. Use counterclockwise direction.
Refer to the figure below for the mechanism. If link 2 rotates at a speed of 60 revolutions per minute in a counterclockwise direction , find the velocity, using resolution and composition method of: A point connecting link 2 to link 3 A point at the center of link 2 A point at the center of link 3 Of the slider Also, locate all the instantaneous centers.