AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 46 kN/m, LAB = 1.8 m, Lec = 3.6 m, and LcD = 1.8 m. Consider the entire 7.2 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). LAB LBC LCD WT305 x 41

AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 46 kN/m, LAB = 1.8 m, Lec = 3.6 m, and LcD = 1.8 m. Consider the entire 7.2 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). LAB LBC LCD WT305 x 41

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A W18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 26 kips, w = 3.4 kips/ft, LAB = 4.0 ft, LBC = 4.0 ft, and LCD = 15.4 ft. Determine the magnitude of the maximum bending stress in the beam. A P LAB Answer: Omax = i B LBC C ksi W LCD D X
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 20 kips, w = 2.4 kips/ft, LAB = 3.2 ft, LBC = 3.2 ft, and LCD= 13.8 ft. Determine the magnitude of the maximum bending stress in the beam. P Omax LAB Answer: i B LBC C ksi W LCD D X
A cast iron beam is of I– section as shown in Figure (3). The beam is simply supported on a span of 5 m. If the tensile stress is not to exceed 20 N/mm2, find the safe uniformly load which the beam can carry. Find also the maximum compressive stress. -80 mm- 20 mm 169.34 mm 200 mm 20 mm N 90.66 mm 40 mm 160 mm Figure (3)
For the state of stress shown, determine (a) the principal stresses, (b) the maximum in-shear stress. Sketch such stresses in a two- element format. 60 MPa 90 MPa Lx 30 MPa
340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum axial stress that each plate will handle. The allowable shear stress of each bolt is 50 MPa and the diameter of each bolt is 20 mm. F F 150 mm F F 50 mm 340 mm
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 21 kips, w = 3.0 kips/ft, LAB = 3.0 ft, LBC = 3.0 ft, and Lcp = 14.2 ft. Determine the magnitude of the maximum bending stress in the beam. A #1 LAB Answer: Omax = i B LBC C ksi W LCD D X
Asiacell|Asiacel K/s Asiacell For simply supported beam with rectangular cross section shown, determine the values and location of the maximum tensile and compressive bending * stresses 1000 lb 400 lb/ft 6 in DV 8 in 10 ft RA Rp
Tow square bars are welded together and loaded axially as shown: Determine The normal stress between A&B The normal stress between B&C The normal stress between C&D The total change in length of the bar Assume : w1 =40 mm, w2 = 50 mm, P1 = 130 kN, P2= 65 kN, and P3 =260 kN. E = 200,000 Mpa original lengths LAB = 100 mm, LBC = 120 mm, and LCD = 130 mm,
1 A rectangular beam has the dimensions (see Fig. 3.2b) b = 250 mm, h = 650 mm, and d = 600 mm and is reinforced with three No. 25 (No. 8) bars so that A, cylinder strength f is 28 MPa, and the tensile strength in bending (modulus of rupture) is 3.27 MPa. The yield point of the steel f is 420 MPa, the stress-strain curves of the materials being those of Fig. 1.16. Determine the stresses caused by a bending moment M 1530 mm. The concrete 61KN-m.
PROBLEM SOLVING 2 The plates are connected by 12-mm bolts in Figure 5. The maximum axial stress of each plate is 20 MPa and the maximum shear stress of each bolt is 14 MPa. Determine the maximum Force F that can be applied to the plates. F F 340 mm D 340 mm Figure 5: Bolted Plates F 150 mm F 50 mm
The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded. Steel 2 ft Bronze 4 ft Aluminum 3 ft 2P 3P 4P A (in.?) E (psi) a. (psi) Steel 0.75 30 x 10 20000 12 x 10 10 x 10 Bronze 1.00 18000 Aluminum 0.50 12000
X Your answer is incorrect. AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P= 19 kips, w = 3.8 kips/ft, LAB = 5.2 ft, LBc = 5.2 ft, and LCD = 14.4 ft. Determine the magnitude of the maximum bending stress in the beam. %3D P. D LAB LBC LCD Answer: ksi Omax 3.45 Cubmit nnwer