Consider a silicon PN step junction diode with Nd = 1016 cm³ and N₁ = 5 × 1015 cm³. Assume T= 300 K. (a) Calculate the built-in potential bi (b) Calculate the depletion-layer width (Wdep) and its length on the N side (x) and P side (xp). (c) Calculate the maximum electric field. (d) Sketch the energy band diagram, electric potential, electric field distribution, and the space-charge profile. (e) Now let Na = 1018 cm³. Repeat (a), (b), and (c). Compare these to the previous results. How have the depletion widths changed?

Consider a silicon PN step junction diode with Nd = 1016 cm³ and N₁ = 5 × 1015 cm³. Assume T= 300 K. (a) Calculate the built-in potential bi (b) Calculate the depletion-layer width (Wdep) and its length on the N side (x) and P side (xp). (c) Calculate the maximum electric field. (d) Sketch the energy band diagram, electric potential, electric field distribution, and the space-charge profile. (e) Now let Na = 1018 cm³. Repeat (a), (b), and (c). Compare these to the previous results. How have the depletion widths changed?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
Consider a silicon pn junction diode at T 300K. The reverse saturation current is Is = 10-14 A and the ideality factor n = 1. Determine the diode current for a diode voltage of VD = 0.573 V and use that to determine the DC and AC resistance of the diode. RDC = 14.13 k rac = 639 Q RDC = 234 Q2 = rac=8Q RDC = 7.00 KQ rac = 307 Q RDC = 1.43 kQ rac = 58 Q
True or False. Please explain. thank you As the temperature increases, the forward voltage decreases in a silicon diode. Then, the graph of the forward bias region will shift to the left.
Here are some statements about a p-n junction diode. Some are TRUE and some are FALSE. i. Applying a negative bias to the p-side and a positive bias to the n-side allows a forward current flow. ii. When the p-n junction is under reverse bias, the Fermi level is continuous across the junction. iii. The forward bias current is made up of holes from the p-side and electrons from the n-side flowing across the junction. iv. Under reverse bias, you can get minority electrons flowing from the p-side to the n-side of the junction. v. To get a large built-in voltage, you need to heavily dope the p-side and n-side of the junction. vi. The built-in voltage (or contact potential) of a p-n junction is typically twice the value of the band-gap of the semiconductor. Which of the following statements is correct: (i) and (ii) are both FALSE (ii) and (v) are both FALSE (iii) and (vi) are both FALSE
Given the clamper circuit below, assume that the value of R and C are large enough sothe voltage across the capacitor does not change significantly during the interval of time.a. Using the simplified diode model, simulate the action of the circuit when the Silicon diode isin forward and reverse bias condition and measure the corresponding output voltage.b. Draw the complete output waveform of the circuit
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
A silicon diode has a forward voltage drop of 1.2V for a forward DC current of 100mA. It has a reverse current of 1μA for a reverse voltage of 10V. Calculate the: a. Bulk resistance b. Reverse resistance c. AC resistance at forward DC current of 2.5mA
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
Consider the diode circuit below, with both diodes having 0.7 V across them when they conduct. V(1) = 10sinwt V (AC)V(2) = 4 V (DC)R(1) = R (2) = 1.3 k(ohm) Over a full cycle of the AC input: 1. Calculate the maximum current through diode 1 (D1). Explain and show all steps. 2. Find the voltage across each resistor. Explain and show all steps. 3. Sketch the current waveform across diode 2 (D2). Label all important points. Explain and show all steps.
• A Si diode at a temperature of 25°C has VD = 0.7V at Is = 10nA. The temperature is raised to 125°C. 1. Calculate ID at 25°C. 2. What is effect of rise in temperature on VD & IS 3. Calculate ID at 125°C.
Calculate the currents passing through the diodes D1 and D4 in the circuit given below. (All diodes are silicon).