D2. When a generator's full-load output voltage is the same as its no-load output voltage it is said to be a) under-compounded b) flat-compounded c) over-compounded d) none of the above D3. The output of an overcompounded DC generator can be lowered by use of a a) rheostat connected in series with the series field b) rheostat connected in parallel with the series field c) rheostat connected in parallel with the shunt field d) none of the above D4. When might it be desirable to use an overcompounded generator? a) never b) always c) to compensate for line loss d) when you need a higher no-load voltage than your full-load voltage

D2. When a generator's full-load output voltage is the same as its no-load output voltage it is said to be a) under-compounded b) flat-compounded c) over-compounded d) none of the above D3. The output of an overcompounded DC generator can be lowered by use of a a) rheostat connected in series with the series field b) rheostat connected in parallel with the series field c) rheostat connected in parallel with the shunt field d) none of the above D4. When might it be desirable to use an overcompounded generator? a) never b) always c) to compensate for line loss d) when you need a higher no-load voltage than your full-load voltage

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter31: Three-phase Alternators

Section: Chapter Questions

Problem 1RQ: What conditions must be met before two alternators can be paralleled together?

See similar textbooks

Similar questions

please answer in bond paper 2. A 20-kW, 230-V DC shunt generator has a voltage regulation of 7.5%. Find the terminal voltage at no-load.
Q- In a DC generator, what will be change in emf induced if flux is reduced by 20% and the speed is increased by 20%.
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
The dc armature resistance of delta-connected alternator measured across its two terminal is 0.8 ohm. The effective resistance per phase is?
A DC generator with 8 pole, duplex lap winding excited with a flux of 3mWb/ pole. The number of parallel path in the winding is A 12 B 8 C 16 D 4
There are 144 slots in a 3-phase, 16-pole, 50 Hz., star connected alternator. There are 4 conductors in each slot and all the conductors in a phase are connected in series. Coil span is 1500 electrical and the flux per pole is 0.05 Weber sinusoidallly distributed. Calculate the emf induced per phase.
The emf generated in each conductor of a 6-pole simplex wave armature winding is 0.48 V. If the armature has 42 slots and 125 commutator segments, and there are four turns per armature winding element, find the terminal voltage of the generator. a. 288 V b. 264 V c. 192 V d. 240 V
Two 30 AC generators are such that one has twice the linear dimensions of the other. The field windings of each are excited to give identical sinusoidal air gap flux density waveform. Both have the same number of stator slots and identical winding patterns. The conductors per slot in big generator in K times that of the smaller one. The value of K to get equal no-load voltage at same frequency is (a)8 (b) 8 1 (d) 7 (c) 4
A short shunt compound generator supplies a load of 20 kW at 500 V. The armature, series and shunt field resistance are 0.10 ohm, 0.05 ohm, and 100 ohms respectively. Find the power developed in the armature. Choices: 24600 W 20500 W 22800 W 25400 W
2. A synchronous generator is connected to an inductive load, please draw phasor diagram to show the relationship between the internal generated voltage of the generator and the terminal voltage across the load. If the same generator is connected to a capacitive load, please draw phasor diagram to show the relationship between the internal generated voltage of the generator and the terminal voltage cross the load again. Explain the difference of the terminal voltage responses at these two types of loads.
A three-winding transformer is connected to an AC voltage source as shown in the figure. The number of turns is as follows: N₁ = 100, N₂ = 50, N3 = 50. If the magnetizing current is neglected, and the currents in two windings on secondary side are 2230° and 22150°, then what is the value of the primary current in Ampere? I 0000000000- N₁ № ₂ Z 00000 00000 Z N3 H I₁₂ I₁₂₁ ¹3
A DC generator has an armature emf of 500 V when useful flux/pole is 20 mWb, and a speed of 625 rpm. The generated emf at a speed of 125 rpm and same flux is