Discuss the advantages and disadvantages of using concrete, steel and timber in mild weather regions.

Q: Determine the net length of crest and estimate the shape of downstream ogee spillway section having…

A: Solution-The giuven values are ,The elevation of crest =89.5mThe design discharge =1.15l/sThe number…

Q: In figure, determine the value of P just sufficient to start the 10°wedge under the 400 Ib block.…

A:

Q: What is the Königsberg bridge problem?

A: Konigsberg was a city in Germany in the past but now it's a part of Russia and is now known by the…

Q: If aquifer hydraulic gradient, hydraulic conductivity and effective porosity are found to be 0.4,…

A:

Q: 59. Show that the maximum shearing stress in a beam having a thin-walled tubular section of net area…

A:

Q: Som

A:

Q: A two-dimensional analysis on the flight of an airfoil is shown in the figure. The airfoil shape is…

A:

Q: Without writing the shear and moment equation, draw the shear and moment diagram for the beam loaded…

A:

Q: The pressure drop per meter length in a smooth horizontal tube in a turbulent flow depends on the…

A:

Q: DF, CE and BD.

A:

Q: Medium lubricating oil (SG = 0.860) is pumped through 1000 ft of horizontal 2-in pipe at the rate of…

A:

Q: Oil sg = 0.84 flowing through a pipe has %3D a total heal loss 3ft from pt.1 to pt.2. As the figure…

A:

Q: Valuation of real properties may be done in many ways. a.) We expect that on a per-square foot…

A:

Q: friction, find the force causes the block to slide.

A: This question has been taken from Mechanics

Q: Following are the results of a laboratory consolidation test on a soil specimen obtained from the…

A: Given, W = 134 gm Ho = 2.541 G = 2.6645 A = 31.3345 cm2

Q: For each of the beams in Problems 624 to 629, compute the moment of area of the M diagram between…

A: We draw moment diagram by parts as it gives simple shapes.

Q: Discuss the anisotropic nature of wood.

A: This question has been taken from building materials

Q: 2-21. Determine the supports A and B of the compound beam. There is a pin at C. 4 kN/m A |C B

A:

Q: A W 360 x 744 is used as a beam to support a concrete floor system. The floor is to carry a total…

A:

Q: Problem 14-27 The conveyor belt delivers crate each of mass M to the ramp at A such that the crate's…

A:

Q: METHOD OF LEAST WORK D. REACTIONS E. SHEAR DIAGRAM F. MOMENT DIAGRAM 35 k 1 k/ft 2 k/ft E A C -10 ft…

A:

Q: Given a cantilever beam, determine the slope and deflection at point A. El is constant. 30 KN/m A B…

A:

Q: PROBLEM 10 For pipe BC, determine the (a) flow rate (m³/s), (b) velocity (m/s), and (b) head loss…

A:

Q: Determine the SLOPE AND DISPLACEMENT at point A. TAKE E = || GPA. THE VALUE OF “I" CAN BE SOLVED BY…

A:

Q: A simply supported wood beam of rectangular cross section and span length, L = 1.2 m carries a…

A: Calculate maximum permissible value of P?

Q: Q1 /A W21 x 68 of A992 steel is used as a simply supported beam with a span Tength of 50 feet. The…

A:

Q: A confined aquifer has a source of recharge. The hydraulic conductivity of the aquifer is 40 m/day…

A:

Q: The beam supports the loads as shown in the figure. Using E=200 GPa, w = 16 kN/m, P = 18 kN and M =…

A:

Q: A permeable soil is underlain by an impervious layer. For the permeable layer, k=0.0052cm/s, H=4m,…

A:

Q: 3. Complete the table and sketch the traverse, assuming no measurements were obtained for line EF.…

A:

Q: For the beam and loadings shown and assun constant, answer the following questions. Us decimal…

A:

Q: A square footing 2 m x 2 m is located at a depth of 1.2 m below the ground surface. The soil…

A:

Q: 2. Water (µ = 1.138x10³ kg/m-s) is flowing steadily in a 30m long and 4cm diameter horizontal pipe…

A:

Q: Two steel columns P (Length L end yield strength , = 250 MPa) and a (length 2L and yield strength =…

A: End conditions are same

Q: Calculate moisture content dry basis using the following values;  FW=25g and ODW=20 g

A:

Q: Based on AASHTO, The term ....... is applied when the frame fractions of the soil have a plasticity…

A: When fine fraction of the soil have plasticity index 10 or less than 10, it is classified as silty.…

Q: Design a two way slab using the Coefficient Method considering an interior panel (Case 2). The slab…

A:

Q: What is the flow of the main channel in m3/s if n = 0.020 and side slopes 2H:1V? What is the flow of…

A:

Q: rest on a continuous lateral bracing, check the adequacy of the steel section.

A: Solution: Section details, ASTM steel designation type= A36 W14x68  Steel yield stress (Fy) = 248…

Q: From a given inorganic soil, the following are known: Percentage passing No. 4 Sieve - 100…

A:

Q: 3V/bh located at the midpoint of the altitude.

A: This question has been taken from mechanics

Q: Find the apparent weight of a man

A: a=(v-u) / t = (5-0)/4 =1.25 m/s2

Q: USING MOMENT DISTRIBUTION METHOD G. FEM = H. DF = I. REACTIONS = J. SHEAR DIAGRAM = K. MOMENT…

A:

Q: Solve the problem with complete and neat solution. Draw the figure. 1. Compute the support reactions…

A:

Q: PROBLEMS 5.4-5.6 Draw the shear and bending- moment diagrams for the beam and loading shown. C D L…

A:

Q: Determine the slope at A and displacement at C. El is constant. 5 kN-m -1.5m- -1.5m-

A:

Q: What are the active earth pressure coefficient and passive earth pressure coefficient of soil, if…

A:

Q: PROBLEM 9 Heavy fuel oil flows from A to B through 3000 ft of horizontal 6-in steel pipe. The…

A: (a) What is the head loss (ft) between A and B? (b) Assuming laminar flow, what is the velocity…

Q: 200 kN 25 kN/m A B Hinge Hinge |3 m+3 m+-6 m+ 6m 6 m-

A:

Q: Title: DESIGN OF BEAM (SHEAR) PROBLEM: A rectangular beam has a clear span of 8.0 m and carries a…

A:

Management of Materials

Materials form the basic ingredient or the raw supplies before the final product. Materials cover the inventory storage in typical warehousing. All manufacturing processes and production processes require different materials.