For studying of a dam in the laboratory, a model overflow has been built in the scale of , to 36 Prototype. The flowrate of the flow in the model is 0.15 . The required time for moving of water between two points in the model is 1 minute. Calculate: i. The volume flowrate in the prototype. ii. The required time for moving of water between the points in the prototype.

For studying of a dam in the laboratory, a model overflow has been built in the scale of , to 36 Prototype. The flowrate of the flow in the model is 0.15 . The required time for moving of water between two points in the model is 1 minute. Calculate: i. The volume flowrate in the prototype. ii. The required time for moving of water between the points in the prototype.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) The kinematic viscosity of a fluid used for model is one third of the kinematic viscosity of the fluid used for prototype. During testing of the model, if viscosity and gravity forces are predominant, find the scale ration, velocity ratio and discharge ration
A prototype ocean platform piling is expected to encountercurrents of 150 cm/s and waves of 12-s period and 3-mheight. If a one-fifteenth-scale model is tested in a wavethe channel, what current speed, wave period, and wave heightshould be encountered by the model?
17. The moment of viscous liquid bctween two cylinder depend on angular velocity o of internal cylinder, cylinders diameters d, D., absolute viscosity u. Find the dimensionless parameters and obtain the similarity of dimensionless parameters. M= f(d.D.
Q: Consider a drag force is F is exerted on a sliver by the pressurized air as it moves through the nozzle for air jet spinning as shown in Fig attached. Physical factor influence the drag force F on the sliver is the diameter of the nozzle D: also the velocity of the sliver V. The fluid properties involved are the density p and the viscosity of the air jet p. Derive an expression for the drag on the sliver by the jet of air applying Buckingham Pi theorem.
Here are these questions if I could get help with themIf a spherical storage tank holds 40,000 gallons (120,000 liters) of water,what diameter must it have?If a cylindrical storage tank has a 40-foot (12 m) diameter circular 05::=how high must it be to hold 1 million gallons (3 million liters)?If water is moving at a rate of 3.2 ft3/sec (90,000 cc/sec), how manygallons (liters) per minute is this?If the specific gravity of gold is 19.0. what is the weight of a cubic inch(cubic centimeter) of gold? A cubic foot (cubic meter)?
The force (F) exerted by a flowing fluid on a stationary square plate of height (L), velocity (V) of the fluid, Density (ρ) of the fluid, viscosity (μ) of the fluid and acceleration (g) due to gravity. Find an expression for the force using Buckingham pi theorem.
Assume that the wall shear stress, Tw, created when a fluid flows through a pipe (see Figure a) depends on the pipe diameter, D, the flowrate, Q, the fluid density, p, and the kinematic viscosity, v. Some model tests run in a laboratory using water in a 0.2-ft-diameter pipe yield the Tw vs. Q data shown in Figure b. Perform a dimensional analysis and use model data to predict the wall shear stress in a 0.3-ft- diameter pipe through which water flows at the rate of 1.5 ft3/s. 0.7 Diameter = D 0.6 2 0.5 0.4 Model data (a) 0.3 0.2 0.1 0.5 1.5 Flowrate, Q, ft/s (b) Tw Ib/ft2 Wall shear stress, T,, Ib/ft? n * m N -
You are doing a problem that requires Reynold's Transport Theorem with Conservation of Mass. You carefully write the equation and then on the second line you write: 0 = v3 A3 - Svị dA1 + f vzdA2 What statements in the question or assumptions you make would lead you to this simplification? Mark all that apply. The flow is steady. Newtonian Fluid Incompressible fluid. Inviscid fluid. Inlets have uniform flow. Exits have uniform flow. Velocity is only in the x-direction.
Ex. The force required to tow a 1:30scale model of a motor boat in a lake at a speed of 2m/s is 0.5 N, Assuming that the viscosity resistance due to water and air is negligible in comparison with the wave resistance, calculate the corresponding speed of the prototype for dynamically similar conditions. What would be the force required to propel the prptype at that velocity in the same lake? Ans.: 10.95m/s, 13500N
Q4: Use dimensional analysis to show that in a problem involving shallow water waves (Figure 1), both the Froude number (Fr = and the Reynolds number (Re pch. are relevant dimensionless parameters Fr = f (Re). The wave speed c of %3D waves on the surface of a liquid is a function of depth h, gravitational acceleration g, fluid density p, and fluid viscosity u. P. u Figure 1
Cakulate the time rate of change of air density during expiration Assume that the lung (Fig. 3.11) has a total volume of 6000 ml, the diameter of the trachea is 18 mm, the airflow velocity out of the trachea is 20 cm/s, and the density of air is 1.225 kg/m. Also assume that lung volume is decreasing at a rate of 100 mL/s. Hello sir, I want the same solution, but in a detailed way and mention his data, a question, and a solution in detailing mathematics without words. Solution We will start from Eq. (3.24) because we are asked for the time rate of change of density. We are asked to find the time rate of change of air density; this suggests that Example 3.5 condis tions are representing a nonsteady flow scenario. In addition, we were told what the rate of change in the lung volume is during this procedure, further supporting the use of Eq. (3.24). pdV+ (3.24 ams Assume that at the instant in time that we are measuring the system, density is uniform within the volume of interest. This…
A simply supported beam of diameter D, length L, and modulus of elasticity E is subjected to a fluid crossflow of velocity V, density p, and viscosity u. Its center deflection & is assumed to be a function of all these variables. Part A-Rewrite this proposed function in dimensionless form.