For the amplifier circuit shown below, let R=0.5 KO, R1=56 KO, R2=12.2 KO, Rc=2 KO, RE=0.4 KO and B-100, then answer the Vcc= 10 V RC R1 R, CI wwHH following R2 RE a) Name the configuration of this amplifier b) Perform DC analysis on the amplifier circuit to find Ico leo leo VcEO ) Draw the DC-load line. ww

For the amplifier circuit shown below, let R=0.5 KO, R1=56 KO, R2=12.2 KO, Rc=2 KO, RE=0.4 KO and B-100, then answer the Vcc= 10 V RC R1 R, CI wwHH following R2 RE a) Name the configuration of this amplifier b) Perform DC analysis on the amplifier circuit to find Ico leo leo VcEO ) Draw the DC-load line. ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. Calculate the current gain, the input resistance, and the output resistance.
Figure 1(a) shows a series fed class A amplifier circuit. In order to achieve the maximum efficiency, the Q point must be located at the center of the DC load line as shown in Figure 1(b). This generates the maximum output current swing of Icmax (p – p) RC and the maximum output voltage swing is VCEmax(p – p) = Vcc Assume that the maximum input de power is (1 Vcc Pimax(dc) = Vcc!cQ(max)=Vcc \2° Rc. 2Rc Find the maximum efficiency, 7 of this circuit.
VR2 (t) voltage will be calculated by analyzing the circuit in Figure 2 with a non-linear element using the Small Signal Analysis method. For this purposea) Find the operating point VkQ, IkQ voltage and current values of the nonlinear element.b) Linearize the non-linear element at the operating point.c) Find the voltage VR2 (t) by calculating the effect of the variable source using the linear model.
Q4. For the circuit shown in Figure Q4: i) What is the type of MOSFET and the amplifier configuration? ii) Find the Q-point (Ip and Vps) iii) What is the device transconductance, gm? iv) What are the voltage gain and output voltage? v) Draw the input /output voltage waveforms showing the phase relationship between them. Be sure to label them properly. +20V IDON = 15 mA@ VcsON = 6V VGSTH = 1V 1kQ Rp C2 10M2 Ro1 out Vin 3.3MQ Ra, 47003 Rs 50mV Figure Q4
The transistor parameters for the circuit in Figure are B, =B2 = 100, VBE1on) = VBE2ton) = 0.7 V, and %3D VA1 =VA2 =0.Find the small signal voltage gain Av = vo/vs. (Note that V-=0.026 V) Vcc=9 V Rib Q1 Vs 1 ko -Ro 20 V 100 Q -ww
This problem is AC analysis problem. DC analysis is not needed to answer the question. A) Convert this bias circuit into a bypassed common source amplifier that has an output across a load resistor (RL). To do this you should draw three capacitors on the figure below, an input voltage source, and any resistors you think that should be added. B) In the space below the figure, Draw the hybrid n model for this amplifier circuit including all voltages and resistors. Label Vi, Vgs, and vo on the model. Assume the capacitors you add act as short circuits at AC. Be sure to include resistors R1, R2, R3, R4, and RL in the hybrid pi model. > When you "verify" a mode of operation you will need to calculate all three voltages (Vc, V8, VE for BJTS and VG, Vs, Vo for MOSFETS) and show the correct two conditions are satisfied. > Assume Capacitors acts like open circuits at DC and short circuits for AC. > Assume the following: o Beta = 100 O VBE = 0.7 12V o V (Thermal) = 26 mV o V (Threshold) = 2V O…
5, a) Determine Vdsat when ID=.5 mA. b) Determine Kn when ID = 0.5 Amps. (Show your work!) c) Determine VTN. (Show your work!) d) Vgs Consider the circuit and corresponding graph, shown below. ID (mA) 0.60 0.50 0.40 0.30 0.20 0.10 0.00 0 0.5 Vds 1 1.5 2 2.5 Vds 3 3.5 4 4.5 5 -Vgs = 1V - Vgs = 1.1V - Vgs = 1.2V - Vgs = 1.3V
Fill in the table VB VC VE Ic LE I8 fre IT gm 5V Consider the circuit given at the right. 600k 1.5k =0.7, Vauo, B=165) 100uF Vo 1k 100uF a) Perform DC analysis and calculate all VB =? VC:? branch currents, node voltages, and small signal parameters 3K VE=? Rout b) Draw a small-signal equivalent model n Vin Rin 400K c) Calculate Ri, Rout, and Ay=Vou/Vin -5V
1. Consider an inverting operational amplifier circuit with Ri = 10kohms and Rf = 50kohms. a. Determine the closed loop voltage gain b. Determine the input impedance of the circuit. c. Determine the ideal output impedance of the circuit. d. Determine the peak input voltage, Vi(peak) for which linear operation is possible. e. Determine the output voltage for each of the following values of input voltage. 2. Assume that for the circuit in problem1, for Vi = -2V, assume that an external load RL=2kohms is connected to the output. Determine the total op amp output current.
Compare hybrid model circuit and re model circuits. Which circuit are you going to recommend in solving AC signal amplifier stage. Defend your answer
Design a linear amplifier, based on a bipolar junction transistor 2N3904 in common emitter configuration. The supply voltage is 28V. The quiescent operating collector current for the amplifier should be around 10mA. The data sheet for the transistor shows that the DC current gain at this operating current is about 200. Draw the circuit diagram of your design. Label all the components in the circuit. Show all the voltages and currents that you use for calculations in your design. Label them using consistent naming convention.
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration