For the truss loaded as shown, determine the equation for the line of action of the stand-alone resultant R and state the coordinates the points on the x- and y-axes through which the line of action passes. All triangles are 3-4-5. Assume F₁ = 25 KN, F₂ = 30 kN. F3 = 35 kN, F4 = 25 kN, and M = 105 kN-m. 6 m H Answers: 8 m x-axis: x= -1.04 y-axis: y= B i 1.38 M Equation of line: y = i 1.32 D F, m m X+ 1.38 3

For the truss loaded as shown, determine the equation for the line of action of the stand-alone resultant R and state the coordinates the points on the x- and y-axes through which the line of action passes. All triangles are 3-4-5. Assume F₁ = 25 KN, F₂ = 30 kN. F3 = 35 kN, F4 = 25 kN, and M = 105 kN-m. 6 m H Answers: 8 m x-axis: x= -1.04 y-axis: y= B i 1.38 M Equation of line: y = i 1.32 D F, m m X+ 1.38 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Five forces are applied to the beam trolley as shown. Determine the y-coordinate of the point on the y-axis through which the stand-alone resultant R must pass if F = 3.8 kN and e = 22°. Point O is at the center of the I-beam. 2.1 kN 530 mm 65 mm 4.4 kN 210 mm 0.6 kN 0.6 kN Answer: y = mm
Q2/ Determine the resultant moment of the forces about point B F=400N 100 N D 30° A 45° 0.3 m B Iroon tozm t 100 N 0.4 m 0.2r
The steel bars AC and BC, each of cross-sectional area 120 mm2, are joined at C with a pin. Determine the displacement of point C caused by the 15-kN load. Use E = 200 GPa for steel. 04. A 35° 35° SUMMARY OF ANSWERS 2.5 m 2.5 m Ус mm C 15 kN CS Scanned with CamScanner
Asap
For the loaded beam shown, using moment - area method. a. Determine the value of ElS at mid span and under the concentrated load t b. Determine the deflection at mid span and under the concentrated load Use = 200 GPa and l=65.0x106 mmª. 24 kN 18 kN/m A B -1.5 m-→--1.5 m– 3m
Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x250 mm section and E = 200 GPa. Show complete and organized solution. a. Vertical Reaction at C in kN. b. Moment Reaction at C in kN-m. c. Deflection at point B in mm. d. Maximum deflection on the beam in mm Given: a- 4m b- 24kN/m c- 9kN
Example:Determine the force Pneeded to lift the load. Also, determine the proper placement x of the hook for equilibrium. Neglect the weight of the beam. 0.9 m 100 mm 100 mm 100 mm P. B 6 KN
From the given beam loaded has shown; Determine the deflection at point D in mm. Using Moment Area Method. Let P =37 kN. EI = 14220kNm2 | 2P D B A - 2P 3.0 m 1.5 m 1.5 m Moment diagram by Parts 3P -3P Deflection curve diagram
2. As shown in the figure, a rigid beam with a negligible mass is pinned at O and supported by 2 rods, identical except for length. If P-30KN, a. Find the load in rod A.(KN) (L b. Find the load in rod B.(KN)! c. If rod A elongates by 2 mm, how much is the elongation of rod B.(mm) 2m- -2m- 1.5m- 28g 1126 L=1.5m L=2m P=30 kN B
For the truss loaded as shown, determine the equation for the line of action of the stand-alone resultant R and state the coordinates of the points on the x- and y-axes through which the line of action passes. All triangles are 3-4-5. Assume F₁ = 25 KN, F₂ = 30 kN, F3 = 35 KN, F4 = 25 KN, and M = 105 kN-m. A 6 m H C Answers: x-axis: x= 8 m Equation of line: y = 1 y-axis: y = 1 F₂ B с M D m m X+ 1 m
2. Determine the location of the center of gravity of a wire with uniform cross- sectional area and specific weight., shown in the figure below. The wire is in the form of a broken line P, P2 P3 P4, with P:(-3, 7), P2(-1, 1), P3 (3, 5) and P. (5, 3). C.G. (0.30, 3.60) Pi-3, 7) P(3, 5) M(-2, 4) 8 M5(1, 3) XM(4, 4) PA(5, 3) P2(-1, 1)
4. An overhanging beam AC carries a linearly varying load as shown below. Determine the position and the magnitude of the maximum positive bending moment. (Ans. Mmax 310Nm at x=2.12m from point A) A -1m- BA 1000N/m -2m- 5. Write the shear force and bending moment equations at any point of the simply supported beam shown below. Plot the corresponding diagrams.(Ans. Mmax-12000Nm) -12m- 1000N/m