Full Screen Accessibility While titrating 50.0 mL of a 0.582 M solution of HCI with a solution labeled "0.500 M KOH," you overshoot the endpoint. To correct the problem, you add 10.00 mL of the HCl solution to your flask and then carefully continue the titration. The total volume of titrant needed for neutralization is 71.9 mL. What is the actual molarity of your KOH solution? Round to three decimal places. M %3D

Full Screen Accessibility While titrating 50.0 mL of a 0.582 M solution of HCI with a solution labeled "0.500 M KOH," you overshoot the endpoint. To correct the problem, you add 10.00 mL of the HCl solution to your flask and then carefully continue the titration. The total volume of titrant needed for neutralization is 71.9 mL. What is the actual molarity of your KOH solution? Round to three decimal places. M %3D

Chemistry: Principles and Practice

3rd Edition

ISBN:9780534420123

Author:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Publisher:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Chapter16: Reactions Between Acids And Bases

Section: Chapter Questions

Problem 16.54QE

See similar textbooks

Similar questions

This is about determinition of acid content in vinegar through titration, please answer the questions. Please answer only the items nummber 4-5. i only put other questions for guide. 1. What is the purpose of standardization? 2. What is the primary standard used (name and formula)? ANS: KHP 3. Suppose that the KHP is not completely dry. Will the reported molar concentration of the sodium hydroxide solution be higher, lower, or unaffected? Explain. 4. In preparing the buret for titration the final rinse is with the NaOH titrant rather than with distilled water. Explain. 5. The procedure suggests the addition of only 2 drops of phenolphthalein. What will be the effect to the analysis if larger amount of phenolphthalein is added?
4) The next 9 questions are related to the titration of 20.00 mL of a 0.0750 M acetic acid solution with 0.0700 M KOH. What is the volume of the solution at the equivalence point (in mL)? (This is the total volume, titrant added plus original volume of the analyt\ e solution) ((The answer is not 21.42 or 41))
What volume of 0.85 M NaOH (in mL) is needed to reach the equivalence point in a titration of 83.0 mL of 0.90 M HCIO4? Your Answer: Answer units
Construct a rough plot of pH versus volume of added base for the titration of 50 mL of 0.045 M HCN with 0.075 M NaOH. Ka = 4.0*10-10 for HCN (a) What is the pH before any NaOH is added? (b) What volume of base, in milliliters, is required to reach the equivalence point? (c) What is the pH at the equivalence point? HopHelpCh17N8(d) What indicator would be most suitable to determine the endpoint?HopHelpCh17N9
Given for nos. 10-11: In an acid-base titration, you were given with a 0.1050 M sodium hydroxide solution placed in a buret and is needed to neutralize 20.0 mL of 0.1500 M sulfuric acid. 10. How much moles of sulfuric acid is found in the 20.0 mL solution of a 0.15M H2SO4? Answer: Computation: 11. What volume of 0.1050 M sodium hydroxide solution is needed to neutralize 20.0 mL of 0.1500 M sulfuric acid? Answer: Computation: 12. Draw and label a complete laboratory set-up of acid-base titration using phenolphthalein as the indicator, using HCl as the analyte/sample, and using NaOH as the standard solution. Cite complete source/(s) if picture will be copied from the internet.
l Verizon LTE 7:55 PM O 4% C Question 8 of 8 Submit Which of the following accurately describes the major species in solution at point C on the titration curve for the titration of NH3 with HCl? pH C 7 В D mL H+ A) NH; and H* Tap here or pull up for additional resources A
Consider the titration of a 23.0 mL sample of 0.110 M HC₂H3 O2 with 0.120 M NaOH. Determine each of the following. - the pH at one-half of the equivalence point Express your answer using two decimal places. pH = Submit Part E pH = ΠΙ ΑΣΦ the pH at the equivalence point Express your answer using two decimal places. Submit Request Answer VE ΑΣΦ Request Answer Pearson ? ?
Questions 30-35 refer to the same weak acid/strong base (WA/SB) titration. Prior to the beginning of the titration, there were 0.0090 moles of hypobromous acid present in the flask. The Ką of hypobromous acid is 2.8 x 10-9. (Q30) A 30.00 mL solution of 0.300 M hypobromous acid (HBRO) is being titrated with a solution that is 0.600 M in lithium hydroxide (LIOH). What is the initial solution pH (i.e., when 0.00 mL of titrant have been added)?
13,How many milliliters of 0.0854 M NaOH are required to titrate 25.00 mL of 0.1250M HI to the equivalence point? Group of answer choices A, 17.08 B, 17.1 C, 36.6 D, no correct answer E, 36.593
hi, can you reexplain the 0.6149 g * 1 mol KHP204.22 g= 0.003011 mol KHP Moles of KHP(KHC8H4O4) used in second titration = 0.003011 mol (Answer)
A 10.00-mL aliquot of a known HCl solution (3.800 g/L) was titrated with a 4.100 g/L NaOH solution. Calculate the range of the blank corrected titration volumes using the titration data below: Blank Trial 1 Trial 2 Trial 3 Initial Volume (mL) 12.50 0.50 12.30 34.75 Final Volume (mL) 13.10 10.45 22.35 45.27
Be sure to answer all parts. Find the pH during the titration of 20.00 mL of 0.1000 M butanoic acid, CH3CH₂CH₂COOH (K₁-1.54 x 10-5), with 0.1000 M NaOH solution after the following additions of titrant. (a) 15.00 mL: pH = (b) 20.60 mL: pH = (c) 26.00 mL: pH = Gui