Gear shaft ABCDE is subjected to the torques shown in the figure. Find the internal torque in each seg- ment, and then plot the torsional moment diagram. Assume that the spacing between gears is constant, i.e., 10 in. T, = T2 = 1000 lb-in. 500 lb-in. A B T3 = Ta = 800 lb-in. 500 lb-in. C d = 1.0 in. D T; = 800 lb-in. E

Gear shaft ABCDE is subjected to the torques shown in the figure. Find the internal torque in each seg- ment, and then plot the torsional moment diagram. Assume that the spacing between gears is constant, i.e., 10 in. T, = T2 = 1000 lb-in. 500 lb-in. A B T3 = Ta = 800 lb-in. 500 lb-in. C d = 1.0 in. D T; = 800 lb-in. E

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. The center distance of two pair of meshing spur gears 4 = a, =160mm m, = m, z, = 20 3 = 30, 2, = 50 . Calculate the module of four gears and the tooth number of gear 1.
The figure shows a pair of shaft-mounted spur gears having a diametral pitch of 5 teeth/in with an 18-tooth 20° pinion driving a 45-tooth gear. The power input is 28-hp at 1700 rev/min. Find the magnitude of the force acting on bearing D. 3 2 3 in 3 in The magnitude of the force acting on bearing Dis lbf.
Ex. #5] Pinion 2 in the figure runs at 1 750 rpm and transmits 2.5 kW to idler gear 3. The teeth are cut on the 20° full-depth system and have a module of m= 2.5 mm. Draw the free body diagram of gear 3 and shows all the forces acting upon it. Determine the forces acting upon gear 3. The direction of rotation of gear 3, as shown, is counterclockwise. GIVEN: Figure shown N₂ = 1750 rpm $=200 P = 2.5 kW m = 2.5 mm 3 0₂ REQUIRED: CS Draw the freechody distram of gear 3 and compute the forces acting on it.
Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the counterclockwise direction. The gears have a module of 5 mm and a 20° pressure angle. Gear 3 is an idler (b) Find the torque T4c that gear 4 exerts on shaft c.
A pair of helical gears, the rotating direction n1 and helix direction of the pinion 1 are shown in the Figure. Determine: (1) The rotating direction n2 and the helix direction of gear 2; (2) Draw the direction of the radial force Fr, tangent force Ft and axial force Fa for both gears. n 1 n 1 1 Problem 4) Figure
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Figure. The shaft is mounted on two bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 (ou = 750 N/mm?). The factors kp and k; of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 400 400 270 250, 640 210 640 100
ASAP
The top half of a compound Epicyclic gearset is shown in Figure, with input shaft I rotating at a constant speed of 700 rpm in a clockwise direction and generating 12 kW input power. The Annulus wheel A2 isform a compound wheel with gear O and connected to an auxiliary gear N on shaft X. . The Annulus A1 rotates in a counter-clockwise direction at a speed of 5,300 rpm. Calculate the following using this condition: The speed and direction of output shaft O (NO), shaft X (NX) and gear ratio (n). If Annulus wheel A1 is locked calculate the speed and direction of output shaft O (NO), shaft X (NX) and gear ratio (n). The braking torque (Tb) (magnitude and direction) that must be applied to Annulus wheel A1 to hold it stationary, assuming gear transmission efficiency is 90%. Number of gear teeth:P1 = 30 , A1 = 120P2 = 50 , A2 = 140N = 60 , O = 120
Form the figure below, the power transmission shaft shows the forces acting on it carrying two gears. The gears are keyed at B and D. A and C are journal bearing centers. Ten hp is transmitted at 750 rpm of the shaft. Assume allowable stress for an unkeyed section equal to 12,000 psi and use Km=K¡ = 2.0. What is the approximate shaft diameter in inches? 4 in 8 in 3 in 320.15 450 lb 105 !b sis lb Do not include the units in encoding the answer. Two decimal places only.
A compound gear train with gears P, Q, R and S has number of teeth 20, 40, 15 and 20 respectively. Gears Q and Rare mounted on the same shaft as shown in the figure below. The diameter of the gear Q is twice that of the gear R. IF the module of the gear Ris 2 mm, the centre distance in mm between gears P and Sis Q S P R I I 1
Required information A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force FB at the pressure angle shown. Given: FA = 450 lbf, diameter of gear A = 19 in, and diameter of gear B=7.6 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 1.25-in dia. FA Gear A 16 in 20⁰° 14 in Gear B 9 in FB 20⁰ Find the bearing reaction forces, assuming the bearings act as simple supports. The magnitude of the bearing reaction force Rcy is The magnitude of the bearing reaction force Roy is The magnitude of the bearing reaction force Rcz is Ibf. lbf. Ibf.
A pair of helical gears, the rotating direction n¡ and helix direction of the pinion 1 are 4) shown in the Figure. Determine: (1) The rotating direction n2 and the helix direction of gear 2; (2) Draw the direction of the radial force Fr, tangent force Ft and axial force Fa for both gears. n 1 n 1 1 2 Problem 4) Figure