has a mass of 75 kg.6-90 The plate shown in Fig.The brackets at supports A and B exert only force reactionson the plate. Each of the brackets can resist a force alongthe axis of pins in one direction only. Determine the reac-tions at supports A and B and the tension in the cable.GOD1.2 mB30°1.4 m2 m

Write the position vector of the points A, B, C and D.

Answered: has a mass of 75 kg. 6-90 The plate…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The collar C is fixed to rod AB using a glued bond that allows a maximum force of 405 N parallel to the axis of the rod. The collar has weight W acting in the negative z direction. Determine the weight W in N of the collar that will cause the glued bond to break as shown in figure.
The system is made up of a bar, supported by a pin at point A and by a smooth collar at point B (the collar slides on the ABG bar). The collar is pinned to bar BDE, and bar BDE is supported by a pin at D and a cable at end E. Determine the force P such that the force in the cable equals to T. With T= 26 lb, a=4 in, b=9 in
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 19i - 14j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. %3D 2 m C 4 m 6 m y Answer: Calculato the madnitude of the tension in cable BD in kN. ere to search 3m 6m
Situation 6 - The 360-N box is held in place on the smooth inclined surface by the rope AB. Determine the following: 16. The tension in the rope in N. Answer: 318.44 N 17. The normal force exerted on the box by $30 the inclined surface, in N. Answer: 390.62 N 509 Flgure AP-4.16
30 cm 18 cm Hom Scm Hom Sum 2. The 30 cm handle is connected rigidly to the 5cm bar at a right angle. Determine the force developed at A if a force P = 100 N is applied perpendicular to the handle when the handle is at the position indicated.
Determine the reactions at supports A and B and the force exerted by the pin at C on member BCD of the frame shown in Fig. 1000 Ib 2 ft B C 45° 1500 lb 4 ft 500 lb/ft A F1 ft -4 ft- l ft -4 ft-
As shown in the image below, the 87-lb crate is supported by three ropes as shown. The coefficients in the coordinates are a=4.7, b=3.8, and c-7.1. Determine the tension force in cable OC, in lb.
The uniform 18kg Bar OA is held in the position shown by a smooth pin at 0, and the cable AB which is in tension as shown. 1.5 m 60° B -1.2 m What is the magnitude of the Vertical reaction force at O (Answer in Newtons) Answer: Nex
An overhead crane is used to reposition the boxcar within a railroad car-repair shop. If the boxcar begins to move along the rails when the x-component of the cable tension reaches 510 Ib, calculate the necessary tension Tin the cable. Determine the angle 8 between the cable and the vertical x-y plane. Answers: 685.275 lb 18.435
1. The rectangular plate is suspended from verti- cal cables and is in equilibrium. The mass, m, of the plate and the dimension d are given. The weight of the plate acts through the center of the rectangle. What are the tensions T4, T; and Tc in each of the three cables? 1.5d B 2.5d 10.75d d H
Q2. Determine all forces acting on body A for the system shown in figure 2. Body A weighs 200 N and the cylinder B weighs 500 N. assume all the contact surfaces are smooth. 777TT ring 24 Cable A r=05 m 30 0.5 m 1 m 1m
The arm in the figure below weighs 41.6 N. The force of gravity acting on the arm acts through point A. Determine the magnitudes of the tension force Ft in the deltoid muscle and the force Fs exerted by the shoulder on the humerus (upper-arm bone) to hold the arm in the position shown. F 0.080 m -0.290 m TE br

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS