If the reaction temperature is too low, little reaction occurs and only a small amount of product is produced (little formation of B) If the reaction temperature is too high, most of primary product B reacts to form a lower-value secondary product (too much of B reacts to form C). So there is a temperature between these limits that maximizes the profitability of this reactor Consider the following data for the cost and values of A, B, and C Cost and value: V-$0.15/mol (cost of A in feed) V=$0.10/mol (value of A in product) V-$0.50/mol (value of B in product) V=$0.20/mol (value of C in product) A Use excel for the following calculation a. Select an arbitrary reactor temperature b. Use mole balance equations obtained in previous slides to calculate for CA, CB, and Cc Calculate an objective function (Ø has a unit of $/s) as c. Product value Feed Cost 0=EFCV-FCAOVAF which is Product value Feed cost Ø =FCV+FCBVB+FCcVct FCao VAF d. Repeat the calculation using a different temperature

If the reaction temperature is too low, little reaction occurs and only a small amount of product is produced (little formation of B) If the reaction temperature is too high, most of primary product B reacts to form a lower-value secondary product (too much of B reacts to form C). So there is a temperature between these limits that maximizes the profitability of this reactor Consider the following data for the cost and values of A, B, and C Cost and value: V-$0.15/mol (cost of A in feed) V=$0.10/mol (value of A in product) V-$0.50/mol (value of B in product) V=$0.20/mol (value of C in product) A Use excel for the following calculation a. Select an arbitrary reactor temperature b. Use mole balance equations obtained in previous slides to calculate for CA, CB, and Cc Calculate an objective function (Ø has a unit of $/s) as c. Product value Feed Cost 0=EFCV-FCAOVAF which is Product value Feed cost Ø =FCV+FCBVB+FCcVct FCao VAF d. Repeat the calculation using a different temperature

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a) What is latent heat of vaporization? Latent heat of fusion? b) Assuming a solid material has a specific latent heat of fusion of 334 kJ/kg, what is the energy required to completely melt this material? Mass = 20 kg? c) If the material from part b melts at 200oC and starts at 20oC, what is the total amount of energy required to both bring it to its melting point and melt all of the material? (Cp = 18 kJ/kgK)
When performing a quench to cool a product, the quench rate affects the outcome of the process. TRUE OR FALSE: 3 principal driving forces for the development of mechanical properties during heat treatment. Group of answer choices Microstructure Changes Formation of Surface Oxide Cooling Rate Ambient Temperature Heating Rate Diffusion Rate Heating Method
1. Search and find two-to-three-page information about “Isomerization Plant” in the refinery ,including the details of the process including the process objectives, raw material enters and final products exit the process, flow diagram and descriptions of process.
Which of the following isotherm models account for limiting surface area as adsorption sites become increasingly occupied by the contaminant? Select all appropriate answers. Langmuir Isotherm Any category that is nonlinear The Kaparov model Any category that is linear Feundlich isotherm Generic linear sorption model. None of these apply
Q1:A/ Fill the blanks with suitable answer : 1-The solid phase in the Isomorphism Systems is a is a 2- The line above the mixture phase is called 3- The reaction that results from the separation of a solid phase into two phases is called 4-Phase diagrams are classified based on number of components in the system to the: 1).. . , 2)... 5- The peritectic reaction(in Iron - Carbon phase diagram) result from reacts ... With percent... and gave product. . . Solid, while in Iron - Carbon solid solubility with percent......and ..... with percent
In the solid solution in an alloy sometimes, two phases which are already present interact at a fixed temperature to produce an entirely new phase. This is known as a peritectic transformation. Thus, the peritictic compound may showed the followings: * Depression of the yield point. O None. High strength and ductility. Isolated segregates scattered randomly in the matrix. Laminated layers as a result of the nteraction of the two phases.
H.W.:- An ore is analyzed for manganese content by converting the manganese to Mn3O4 and weighing it. If a 1,52 g sample yields Mn3O4 weighing 0.126 g, what would be the Mn2O3 % in the sample? Mn% in the sample?
1-discribe how manufacturing Process are classified? 2- llustrate the process which work above recrystallization temperature with neat sketch? 3- Discuss the heat treatment process which uses rapid cooling of steel in oil or molten salt bath?
Given the hypothetical thermochemical equation: A + B C + D AH = - 430 kJ Which among the following statements is correct about this reaction? a. The reaction is endothermic. b. The equation may be written as A + B + 430 kJ c. The heat content of C andD is greater than the heat content of A and B. d. The heat content of A andB is greater than the heat content of C and D. C + D
Martensite transforms into austenite through the process of rapid cooling. Question 22 options: True False
Please provide a clear solution, a pv, and a ts diagram.
Match each statement with a letter -In the peritectoid reaction -In the Peritectic reaction: -In the Monotectic reaction: -In the Eutectoid reaction: -In the Eutectic reaction: a. a liquid phase transforms into two solids when it is cooled down b. a solid phase transforms into two different solids when it is cooled down c. a liquid phase transforms into a new liquid phase and a solid phase d. Two solid phases transform into a new single solid phase e. A solid phase and a liquid phase transforms into a solid phase