In a three-phase system, the per-unit symmetrical components of the phase currents areI0 = 0.5 , I9) = 120 , 12) = 0What are the per-unit phase currents Ia, Ib, Ic? Express in polar notation.

Answered: Image /qna-images/answer/000aa314-ddd4-44d3-b829-b768fa1d30f6.jpg

Answered: In a three-phase system, the per-unit…

In a three-phase system, the per-unit symmetrical components of the phase currents are IO = 0.5 , I9 = 120 , I2) = 0 What are the per-unit phase currents Ia, Ib, Ic? Express in polar notation.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.6MCQ

See similar textbooks

Related questions

Q: Use source transformation to find vo in figure shown below: 4 A

Q: Find the power loss in IL utilizing Thevenin's theorem. 1=2 A = 2.0 V3= 4V 2 = 10 =50 b.

A: Thevenin’s theorem: Any linear and bilateral network can be shown as Thevenin voltage and series-con...

Q: 1.What type of transformers do we use to send power out to our power grid? A. Step Up Transformers. ...

A: In power stations to produce the high voltage required to transmit electricity through the Power gri...

Q: Find current thru 3 + j4 ohm impedance use any method. 5Ω 5Ω 3 2 |-j5 N 100/0° V(^ (1) 10/3 j4 N wel

Q: 5. Given the Ri is (5002, 10002, 1500KO, 20002). i. Solve the voltage V, and current I, flow through...

Q: Question 4. Z, = (10+ jl7.32)N , Z, = (20+ j34.6)N, Z,=(25+ j43.3)N, %3D Z, = (10+ j17.3)N, Determin...

Q: Discussion: 1. Simplify the following logical 'expression and implement them using suitable log gate...

A: Note: As per the guide lines of the bartleby we are supposed to solve one question, when they are ...

Q: shunt field

A: DC shunt motor- In DC shunt motor field excitation is connected in parallel with the armature field ...

Q: Create a signal as: x(n)={2,1,1,8,0,1,4,0}, where origin of the signal is at 2. Estimate the spectru...

A: Given that signal xn=2,1,1,8,0,1,4,0

Q: What is threshold voltage?

Q: Find current thru – j5 ohm capacitive reactance use any method. 5Ω 5Ω 3Ω |-j5 Q 100/0° V( 1) 10/30'A...

Q: Find Z Th j60 2 -j48 2 a 240/0° V(A, 36 N +I

Q: A 120 V electrical outlet with 4 A of current flowing from it has a power value of, O 480 W 48 W O 2...

A: As we know that the power can be calculated as: P=V×I where, the P is representing the power (in wat...

Q: Construct a 5 to 32-line decoder with four 3 to 8 decoders, with enable and 2 to 4-line decoder with...

A: Given 5 to 32 line decoder with four 3 to 8 decoders with enable and 2 to 4 line decoder

Q: Calculate the equivalent impedance, with respect to the supply terminals of the circuit with the dia...

Q: 30 Q 25 Q 10 Q 20 Ω a o 15 N bo

Q: induction motor

A: Induction motor- An Induction motor is an asynchronous motor in which a torque is produced by electr...

Q: Design a full-wave rectifier with LC filter to provide 10 V dc at 100 mA along with maximum ripple o...

A: Given 10v DC 100mA Find ripple factor

Q: Y(s) 2. Reduce the block diagrams below to find the equivalent transfer function G(s) Simplify fract...

Q: 1. Phasor: Convert the following voltage and current signals into phasor (both rectangular and polar...

A: Note: As per the guide lines of the bartleby we are supposed to solve 3 questions, when they are i...

Q: Show that 1+ 5i 5 3+ 3' -3i

Q: F16-4. The bucket is hoisted by the rope that wraps around a drum wheel. If the angular displacement...

Q: x(п) 3 () и(-п - 3) а. In| b. x (п) %3D

Q: Design a PLC program that will correctly execute the following industrial control process: A part is...

A: We need to draw and explain the PLC diagram for the given operation. The given operation and conditi...

Q: Calculate the current through the ammeter. 2.0 A 2.0 A R, 2.0 Ą R3 5.0 A Select one: а. 1.0 A b. 2.0...

A: Given circuit,

Q: A three phase, 4 - pole, 50 Hz induction motor has full load speed of 1455 rpm. What will be the fre...

Q: tify three common simple specific electrical gadgets/devices at home; look for its specific schemati...

A: The three common electric gadgets which are used at home are given below : 1. Heater : Heater is a d...

Q: Three zones of a single-phase circuit are identified in Figure. The zones are connected by transform...

A: per unit system The ratio of actual value to the base or reference value in the same unit is called ...

Q: 2. Given the points P(4,7,3) and Q(-3,6, –5) a. Locate P in cylindrical coordinates b. Locate P in s...

Q: 50 ) 25 V + 10Ω + 1)

Q: 4.5-4. Find the z-transform of the following functions. " -0.37s 6ɛ (а) Е(s) (b) E(s) (s + 1)(s + 2)...

A: As per our guidelines we are supposed to answer only first question. Kindly repost the other questio...

Q: 30.0 cm 40.0 cm 30.0 cm 50.0 cm

Q: Are the following statements correct or wrong? Justify your answer. (a) GTO requires very high curre...

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts fo...

Q: A 3-phase, 11-kV, 50-Hz, 10-pole, 200-kW star-connected salient-pole synchronous motor has Xd = 1.2 ...

A: Given thatTerminal voltage VT= 11kV3=6.350VP=200kWXd=1.2puXq=0.8pucosϕ=0.98

Q: A 120 V electrical outlet with 4 A of current flowing from it has a power value of O 480 W 48 W O 24...

A: Given, Voltage, V=120 V Current, I = 4 A

Q: Find voltage across the parallel impedances of the circuit below. -j5 N 5Ω HE 3Ω 100/0° V(A 5Ω j4 2 ...

Q: It Given : VT = Vm cos wt Vm = 310V 2) f = 60HZ = 28 2 R4 L, - 0.06 H Find: Ca) RMS caleu lated volt...

Q: Question 1 Q1: For the circuit shown below calculate (a) the value of resistor Rx such that the tota...

A: Resistance: It is a property of a material that resists the flow of current and its unit is the ohm.

Q: Solve the circuits given, with solutions: EB = 24 volts Redraw diagram indicating where the voltmete...

A: A Voltmeter also known as a voltage meter is a device that measures the voltage or potential differe...

Q: ree-phase lines: • Load 1: Delta-connected, 500KVA at 0.85 lagging Load 2: Wye-connected, 75KVA at u...

A: Given that utility feeder=5milesVL=4.16kV

Q: Find current thru 100V source use any method.

Q: Design a clamper circuit that biases the AC waveform so it lies completely below the zero line.

A: Given circuit has output which is clamped It needs a capacitor and diode This is called negative c...

Q: Find the total current of the circuit below. -j5 N 5Ω 3Ω 100/0° V(A, 5Ω j4 N O 55/29 - j80/29 A O 22...

Q: Consider a discrete time system with the following input output relation y[n] = x[n]x[n – 2] Is the ...

A: Given function yn=xnxn-2

Q: Upload answer sheets i) With a neat sketch explain the construction and operation of a Moving coil i...

A: Since you have asked multiple question ,we will slove the first question for you .If you want any sp...

Q: 10 ν 60 Hz 100 μF

Q: Three impedances Za = 4 - j3 ohms, Zc = 4 + j4 ohms and Zr = 3 + j ohms are connected in parallel. S...

Q: edefine the avuage 4. How do f an ACO wavefloum.? Determine the aaverage value of a full "sectified ...

A: Rectifier: This is an electrical circuit that converts ac into dc. This is used where dc input is re...

Q: A balanced, three phase circuit is characterized as follows: i. Y-A connected i. Source in the c-pha...

Q: A 900 rpm, 6-pole generator has a simplex wave winding. There are 300 conductors on the armature. Th...

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

In a three-phase system, the per-unit symmetrical components of the phase currents are
I0 = 0.5 , I9) = 120 , 12) = 0
What are the per-unit phase currents Ia, Ib, Ic? Express in polar notation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

X₂=0.1 1 XL +03 Soto X₁ = 0.2 X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. b) Find the bus voltages and line currents during the fault. 2 O oto
Q2 (a) Three-phase generator consist of three set of single-phase generators, with voltages equal in magnitude but differing in phase angle by 120° apart. (i) Sketch phasor diagram of the three-phase voltages VA, VB and Vc (ii) Plot the three-phase voltages waveform in Q2(a)(i) in single plot.
The reactance of a generator is given as 0.25 per-unit based on the generator’s of 18 kV, 500 MVA. Find its per-unit reactance on a base of 20 kV, 100 MVA. a. 0.0505 b. 0.0605 c. 0.0405 d. 0.0606
Discuss how delta connection is achieved in three-phase systems?
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
In a three-phase system the per-unit phase voltages are 100° , Vôn = 0.8Z180° Van 0.920° , Von = 0.92 - а What are the per-unit symmetrical components V0) and V)? Express in polar notation.
3 X 0.1 1 2 XL = 0.2 to Eato oto O X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. (2 Marks) b) Find the bus voltages and line currents during the fault. (2 Marks)
In single phase power factor meter there is error due to frequency and waveforms but not in three phase power factor meter, I know the reason why?? Please elaborate properly
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
What is a microgrid?
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
Please help with this balanced three-phase circuit problem.