Mark the correct statement: a) The ISC steps are: Compaction, Expansion and Simple Axial Compression b) The MR Resilience Module measures the variation in stress with permanent deformation, there is no rupture in the test c) The MR Resilience Module can be performed in a triaxial cell and dynamic loading that best represents the pavement

Mark the correct statement: a) The ISC steps are: Compaction, Expansion and Simple Axial Compression b) The MR Resilience Module measures the variation in stress with permanent deformation, there is no rupture in the test c) The MR Resilience Module can be performed in a triaxial cell and dynamic loading that best represents the pavement

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter20: Design Of Rigid Pavements

Section: Chapter Questions

Problem 12P

See similar textbooks

Similar questions

Find the safe static wheel load that a 360 mm thick rigid pavement could carry without any dowel across the joints if the allowable tensile stress of concrete is 1.5 MPa.
A pavement element along Thika road of 100x150x200 mm was subjected to an equalall round pressure of 120kn/m2 and axial load of 2.5KN in the X-direction. The changesin length are 0.92mm in X-direction, 0.27mm in the Y-direction and 0.18mm in the Z direction. Calculate thei. Elastic theory ratio, Eii. Poisson’s ratio,iii. Bulk Modulus, K
1. Figure (1) shows a pavement structure composed of three layers with their details. If the HMA and the base layers are combined into one layer with the same total thickness (HMA+base layers), what should be the equivalent elastic of the combined layer modulus so the tensile strain at the bottom of the the HMA= 0.0006 in. 30000 Ib 150 psi E, = ? 6 in HMA layer Ej = 400,000 psi V;=0.4 Granular base E = 20,000 psi V=0.4 20 in layer Subgrade layer E3 = 10,000 psi Vz=0.4 %3D
A concrete pavement is constructed at a temperature of 10°C. The peak summer temperature is 30°C. The coefficient of temperature is 10 x 10^- 6/°C. The gap at the expansion joint is 2.5 cm. The spacing of expansion joint is what.
Calculate the maximum stress at corner if 4600 kg wheel load is applied on cementconcrete pavement of thickness 180 mm. a) 40 kg/cm² b) 42.59 kg/cm² c) 43.54 kg/cm² d) 44.89 kg/cm²
Q3/Choose the correct answer 1. In general PSI for flexible pavement depend on............ Va. Cracking, Patching and Rutting b. Cracking and Patching c. Patching and Rutting d. Rutting 2. The Maximum contraction joint spacing for plain jointed concrete pavement is C. 3.5 m b. 4.5 m c. 5.5 m d. Depends on traffic load 3. The relationship between A psi and age of pavement is...... a. A psi co age Apsi ∞ (1/age) c. A psi 02(1/age) d. Non of the above 4. The surface of the pavement should be a. Smooth b. Rough 5. Which type of aggregates gives good workability? a. Round b. Flaky c. Angular 6. Rutting may be avoided by a. Good compaction . Sufficient enough to resist skid b. Good drainage 7. Bleeding may be avoided by a. Water voids b. Air voids c. Asphalt type 12. Tie bars in cement concrete pavements are at a. Expansion joints d. All the above acceptable c. High filler percent All the above 8. The good drainage in pavement can La Increase the pavement life b. Decrease the pavement life…
The following figure shows concrete pavement with the layer thickness and elastic modulus as indicated. Assume modulus of rupture of 650 psi, load transfer coefficient of 3.2, serviceability loss from 4.5 to 2.5, and drainage coefficient of 0.9. The bedrock depth and loss of support is not considered for the subgrade. Use the design equation or monograph with 50% reliability to solve the following: 1) Determine the number of ESAL that the pavement can carry before failure. 2) If the daily traffic has 1080 single axles (20-kip), 400 single axles (24-kip), and 680 tandem axles (40-kip), and the annul traffic is the same over the design period, how many years would the concrete pavement last before failure? 8-inch Portland Cement Concrete Ec=4×106 psi 8-inch Granular Subbase Ec=30,000 psi Subgrade Mr = 5000 psi
A rigid pavement is to be used to carry a wheel load of 58.77 kN. Enough dowels will be used across the joint. The allowable tensile strength of concrete is 1.45 MPa. Thus, what will be the difference in thickness (in mm) between the edge and the center of the pavement?
Show complete solution and clear explanation thank you A flexible pavement having a thickness of 46mm carries a static wheel load of W. The circular contact has an equivalent radius of 150mm. If the load W is assumed to be transmitted across a wide are of subgrade at an angle of 45 degrees compute the value of the wheel load W if the bearing stress of the base is 0.42 MPa
20. In the PCA design procedure of rigid highway pavements, the fatigue damage analysis is based on the center-slab tensile stress calculated at the bottom of the slab.a. Trueb. False21. In the PCA design procedure of rigid highway pavements, as the stress ratio (applied flexural stress divided by 28-day modulus of rupture) decreases, the allowable load repetitions increases.a. Trueb. False22. In the PCA design procedure of rigid highway pavements, the fatigue damage is calculated at the pavement edge.a. Trueb. False23. In the PCA design procedure of rigid highway pavements, the erosion damage analysis was devised to control the following distresses:a. Subgrade erosion, pumping and faultingb. Shattered slab and ASRc. Shrinkage cracking and joint sealant deteriorationd. None of the above 27. The PCA design methodology for airfield rigid pavements is based on the interior bending stress at the bottom of the slab.a. Trueb. False
The pavement layer is considered superior if it distributes load like a А. Point load Uniformly distributed load C. Uniformly varying load D. Triangular load B.
5. A rigid pavement is to be used to carry a wheel load of 54.04 kN. Enough dowels will be used across the joint. What will be the difference in thickness (in mm) between the edge and the center of the pavement? The allowable tensile strength of concrete is 1.42 MPa. Round off to the nearest whole number.