Please Answer the following: In the circuit shown, if the transistor has V, = 1.1 V, kn = 1.3 mA/V², and Ip= 1 mA. Find gm and r. if VA = 60 V. Draw a complete small-signal equivalent circuit for the amplifier, assuming all capacitors behave as short circuits at signal frequencies. 1. 2. Find Rin and R.. 3. Find the overall voltage gain v/Vi. 6 V 250 k2 o vo 500 k2 Vi 1.66 k2 Rin R. 루

Please Answer the following: In the circuit shown, if the transistor has V, = 1.1 V, kn = 1.3 mA/V², and Ip= 1 mA. Find gm and r. if VA = 60 V. Draw a complete small-signal equivalent circuit for the amplifier, assuming all capacitors behave as short circuits at signal frequencies. 1. 2. Find Rin and R.. 3. Find the overall voltage gain v/Vi. 6 V 250 k2 o vo 500 k2 Vi 1.66 k2 Rin R. 루

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit of Figure 2. Carry out the analysis in DC and small signal with www.w www www.www Vt=0.7 V, Kn(W/L) = 4 mA/V. Ignore the Early effect. Determine: (a) The current in DC ID. (b) The gains vo/v₁, io/ii (c) The input resistance Rin and output resistance Rout. wwwwww 06402 www Ca HH {ama Ο ΜΩ www.11 Figura 2: 0.51 k www.li 12 V • 27 ΚΩ Ca +1₁ -0% 4.7 k
Solve for the common base amplifier Given B= 100, Si=0.7 (voltage drop) Find a) Avs b) Ais c). What are Ac voltage at each point indicated (A,B,C,D,E) in the circuit with Vs = 100mVp-p
step by step explanation needed. Given a sinusoidal input signal (1 mV amplitude at 5kHz), design a CE-CC amplifier to achieve a 100 mV amplitude sinusoidal signal across a 50ohm load.
Given the MOSFET in Figure 6 has bran) = 200 mA at VGs = 4 V and V(Tn) = 2 V; i. Plot the transfer characteristic curve for the MOSFET. b) i. Determine the operating point Vasa, Ioa and Vosa for the circuit. ii. Calculate the value of the transconductance gm at the Q-point. iv. Determine the voltage gain and input impedance of the amplifier. 15 V 1 kn. Coe 1.5 M2. Cin 33 kn. Vn 30 ka Figure 6
Using LTSpice, simulate the circuit below, use 2N3904 for the transistor. Part ! DC simulation: Measure VCE and Ic. Use .op for the simulation cmd. Remove all capacitors and input signals first. Part 2 AC simulation: Connect all capacitors now and apply an AC signal at the input with an amplitufe of 1mV and a frequency of 1kHz. Determine the Voltage gain of the circuit by dividing Vo with Vin. Show the output for both the DC and AC analysis. Take a screenshot of the circuit and the output voltages and waveforms. Paste in a word file, write your answers, then save as pdf. 50 kΩ Σ 20 0,5 ΚΩ wwwh 9 Vcc=20 V Ca=1 µF = Cc₂ Cg=50 μF 5.6 kn B=100 Ca IST • 3.3 ΚΩ 5 ΚΩΣ CE
For the BJT circuit shown below, sketch the hybrid equivalent model circuit with labels of voltages, impedances, and currents. ... 1.8k0 Vo 39ka 22ko tuF-POL 10UF-POL 1200 1uF-POL 2N2221 100mv 1.5KHZ ODeg
4. For the transistor in the figure shown below, the parameters are ß = 100 and VÀ = ∞. a. Design the circuit such that lEQ = 1mA and the Q-pt is in the center of the dc load line. b. If the peak-to-peak sinusoidal output voltage is 4V, determine the peak-to-peak sinusoidal signals at the base of the transistor and the peak-to-peak value of Vs. If the load resistor R₁ = 1kQ is connected to the output through a coupling capacitor, determine the peak-to-peak value in the output voltage, assuming vs is equal to the value determined in part (b). Vcc=+10 V www Rs = 0.7 kΩ Cc www RB RE vo
1. Assume that the source voltage for the D-MOSFET in the following figure is measured and found to be 1.6 V. a. Compute lo and Vos- b. If gm = 2000 umho, what is the voltage gain? c. Compute the input resistance of the amplifier. d. Is the D-MOSFET operating in the depletion or the enhancement mode? 100 my pp 1.0 kHz HI C₁ 0.1 µF R₁ 5.1 ΜΩ R₂ 10 ΜΩ +VDD +24 V ① RD 2.7 C3 Rs 330 Ω OV ORI C₂ 33 μF
You are tasked with designing a linear amplifier using an NPN BJT for the circuit shown below. This means the transistor iv curves apply here. The voltages given are Vcc = 14 V and Vs = 1.0 V. The datasheet for the transistor says VBE (ON) = 0.7 V,VCE (SAT) = 0.2 V, and ß = 400. The design should have ic = 12 mA and VCE = 8 V. Find the resistances Rb and Rc that give the required ic and VCE. Vs H Rb M d VBE Rc VCE Vcc
Use BJT transistor to design an amplifier circuit that operates in the frequency range 10kHz-100kHz. Verify your design by simulating the design using the circuitmaker or multisim software. Use the standard resistor values (10% tolerance). The design should meet the following criteria: 1. Good stabilization of the Q-point 2. VCEQ is around % VCC. 3. High voltage and Current gain. From your design and simulation results, determine the following: a. B of the transistor b. VCEQ c. The voltage gain (AV)
Use BJT transistor to design an amplifier circuit that operates in the frequency range 10kHz-100kHz. Verify your design by simulating the design using the circuitmaker or multisim software. Use the standard resistor values (10% tolerance). The design should meet the following criteria: 1. Good stabilization of the Q-point 2. VCEQ is around ½ VCC. 3. High voltage and Current gain. From your design and simulation results, determine the following: a. B of the transistor b. VCEQ c. The voltage gain (AV) Please provide us with your simulation file and a report about your results
Use BJT transistor to design an amplifier circuit that operates in the frequency range 10kHz-100kHz. Verify your design by simulating the design using the circuitmaker or multisim software. Use the standard resistor values (10% tolerance). The design should meet the following criteria: 1. Good stabilization of the Q-point 2. VCEQ is around ½ VCC. 3. High voltage and Current gain. From your design and simulation results, determine the following: a. β of the transistor b. VCEQ c. The voltage gain (AV) Please provide us with your simulation file and a report about your results