PROBLEM 8. 1. The critical plate for tension. 2. The maximum load carried by the connection considering tension failure of the plate. 3. The maximum load carried by the connection considering shear failure on the rivet. 4. The maximum load carried by the connection considering bearing failure on the rivet. 5. The safe tensile capacity. 6. The efficiency of the joint. Two plates 14mmx150mm and 10mmx200mm are lapped together using 25mmø rivets as shown. The allowable stresses are: Tension = 100 MPa, Shear = 70 MPa, Bearing = 120 Mpa. Determine the following: 10 x 200 14 x 150 CBA

PROBLEM 8. 1. The critical plate for tension. 2. The maximum load carried by the connection considering tension failure of the plate. 3. The maximum load carried by the connection considering shear failure on the rivet. 4. The maximum load carried by the connection considering bearing failure on the rivet. 5. The safe tensile capacity. 6. The efficiency of the joint. Two plates 14mmx150mm and 10mmx200mm are lapped together using 25mmø rivets as shown. The allowable stresses are: Tension = 100 MPa, Shear = 70 MPa, Bearing = 120 Mpa. Determine the following: 10 x 200 14 x 150 CBA

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 60KN 6m с в от Д 6m D 6m What are the zero force members here? لى) E F G Gy bm H Hy of -Hx
DE TERMINE THE MAXIMUM DEFLEC TION USINE Dou BLE IPPZRATION ME THOD. 2) 5KN lokN 5KN ļ im b im im
1136.) Tho sido rod of the ongine in Fig. P-1136 is 8f long woighs 100 lb. The cranks AD BC aro of longht r 18 in. rotate at 300 rpm. Delorminc the moximum bonding momont M in the rod if M • WL/8, whero w ic the total dictributod load L ie the langht of the nod. ANSWERS: M=100 Ib-ft
Figura P2.43 550 mm 75 mm 100 mm 2.44 La barra rígida AD está soportada por dos alambres de acero de in. de diámetro (E = 29 10 psi), un pasador y una ménsula en. Si se sabe que los alambres estaban originalmente tensos, determine a) la tensión adicional en cada alambre cuando se aplica una carga P de 220 lb en, b) la deflexión correspondiente del punto D. 1 8 in 1 10 in 12 in Figura P2.44 E B 12 in AC P 12 in D
O A 1:1 ملون واضح وثيقة صورة الأصلي Hw For the shown beam -Colymn derive ane tisolve the di ff erential equation of tue deflection aurve, (vegiect self- weight) II 因

a) The components of the apparatus were assembled by the technician. b) Firstly, weigh the aluminium beam given on the measuring scale, with a span of 1000mm. c) Place both spring balances with Newton readings on the left and right end of the frame. 2 d) Zero the two spring balances. e) Load the beam on both spring balances, at Omm from the left end of the beam and at 1000mm on the right end of the beam ) With the use of two metal hangers, place the one metal hanger was at 200mm from the left-hand side of the beam and at 100mm from the right-hand side of the beam, thereafter both hangers will be loaded with loads/weights g) Load left hanger with 400g and right hanger with 500g h) Read and record the readings from both the spring balances as left and right reactions in newtons (N). RESULTS 400g 603.7g 500g 200mm 100mm 500mm 1000mm RL RR Figure 3. Experimental Force diagram of a simply supported beam.
Determine the vatatron at of the frame shown in higuve. E: 2001o mpa I- 3. *1o mm 4 point Take 1ompa I- 3. * lo mmy SEN く。 Lised
A.) CREATE A SHEAR DIAGRAM BY AREA MOMENT AND BY PARTS B.) CREATE A M/EI DIAGRAM BY AREA MOMENT AND BY PARTS ITEM 1.0 25 kN/m A D В C- -3 m-- --10 m- -4 m-| EI = constant E = 200 GPa I = 500(106) mm4
1 An 80-m-long wire of 5-mm diameter is made of a steel with E = 200 GPa and an ultimate tensile strength of 400 MPa. If a factor of safety of 3.2 is desired, determine (a) the largest allow- able tension in the wire, (b) the corresponding elongation of the wire. 33 =p 11 بنا مع 2/2 W Q Search r hp 8:30 AM 3/5/2023
This force-couple system is to be replaced by an equivalent system consisting of the following: a couple moment Mx, and a single force, Rc acting at C. Draw the diagram for the equivalent system and determine Mx and Rc. A 100N 80N 110N-m Thislis not your 50N 150N own propenty so do nbt use it in 50N any way asliffit were your dwn. 130 N D C 180N-m 12° 3ON fhis is hot your own propery so đo not use t n any way as f it were your own. 1m B E
Q24use the Virtual work methad to find the Virticul ound harizantal displacement at joint D. 162 30KN Sm A. 4m 3m 3.
Compule the centroidal distance with respect to X- andy -axs o4 he two figue below- I 2em leem