Ex IRs = Iks Re = 5k2Ao-o JoutRI= Skr R2 = 45 keFor the amplifiersopen-loop gain, A. = lo00 v/Uin put resistance, Rin=25ks2RaRIOveput fesistonce, Rout = Iknfeedbock configuration is this?a) What type of imput- outpot(Example : shunt - shunt, series-sertes, etc)b) Calculate looded open-loop gain, loded open-lop input resistanceloaded open-loop ovtpot resistancec) Calculate loop gaind) Caleulate closed-loop gain, closed - loop input resistance , closed - lonp outpot resistance

Disclaimer: Disclaimer: Since you have posted a question with multiple sub-parts, we will solve the…

Rs Rs = Iks Re= 5k2 %D Ao o Jout Ri= Ske Ra = 45 ks For the amplifiers opon-loop gain, Ao = lo0ulu in put resistance, Rin=25k2 Ra %3D RI RL Oveput fesistonce, Rout = Iko 0) What tg pe of imput - output feedback configurantion is this ? (Example : shunt - shunt, series- series, etc) b) Calculate looded open-loop gain, loodad open-lop input resistance loaded openloop ovtpot resistance c) Calculate loop gain

Rs Rs = Iks Re= 5k2 %D Ao o Jout Ri= Ske Ra = 45 ks For the amplifiers opon-loop gain, Ao = lo0ulu in put resistance, Rin=25k2 Ra %3D RI RL Oveput fesistonce, Rout = Iko 0) What tg pe of imput - output feedback configurantion is this ? (Example : shunt - shunt, series- series, etc) b) Calculate looded open-loop gain, loodad open-lop input resistance loaded openloop ovtpot resistance c) Calculate loop gain

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate the closed loop gain for the following circuit. Assume A = 0 for both transistors and R1+ R2 is very large. Circuit parameters / Devre Parametreleri 9m1 = 49 ms, 9m2 = 33 ms, R, = 101 kn, R2 = 26 k, Rp = 2.2 kn VDD Rp Vout ER Vino ER2 O a. 10.28 O b. 4.67 O c. 8.41 O d. 7.48 O e. 6.54 O f. 3.74 O g. 5.61 O h. 2.80 W WH. w-
Q5) Calculate the gain without and with feedback for the FET amplifier circuit with the following circuit values: VDD R1 = 100 kN, R2 = 25 kN, RĮ = 15 kN, Rp = 12 kN Cp Im = 4000 mS R1 V. RL R2
Q1 Design an operational-amplifier circuit using two inverting configurations to produce the output vo = +201 + 0.5v2 – 0.2v3 – 1v4. Choose feedback resistor Rf = 220kN for each amplifier. %3D | -
The transistor parameters for the circuit in Figure are B1 =B2 = 100, VBE1(on) = VBE2(on) = 0.7 V, and VA1 = VA2 %3D =00.Find the small signal voltage gain Av = vo/vs. (Note that VT=0.026 V) %3D Vcc=9 V Rib Q2 1 ko -R. 20 V 100 Q -14.76 O 0.899 -55.3 ww ww
Q5) Calculate the gain without and with feedback for the FET amplifier circuit with the following circuit values: R1 : = 100 kN, R2 : = 25 kN, Rp = 15 kN, RD = 12 kN + Cp Im = 4000 mS V. RL R2 ::
Q2// Answer the following questions about voltage-feedback bias circuit for the figure below. 1-Determine Ver and VCB. 2- What happens to the voltage Ve if the resistor Rp is open? 22 K 3- What might cause VCE to become nearly 9 V? 4- Determine the change in Ie from 25° to 75° C, if Ico 0.2 HA, and VBE = 0.7V. 10 ul B-80
Adiff-amp is biased with a constant-current source lo- 0.25mA that has an output resistance of R. - 8MO. The bipolar transistor parameters are B=100, VT = 0.025 V and VA -. Determine the common-mode input resistance. O a. Ricm = 538 MA O b.Ricm- 308 MO OC Ricm = 808 MO Od Ricm = 704 MQ
How experimental setup is prepared for a CE transistor configuration. Drawits a h-parameter model. Find amplifier parameters given below using this model- (i) Current gain(ii) Input impedance(iii) Voltage Amplification (AVS) consideration source impedance(iv) Current Amplification (AIS) consideration source impedance
Introducion to Electronic Analysis and Design - CE05 To have a good amplifier Select one: a. The input resistance should be high b. the output resistance should be high c. the voltage gain should be equal to zero d. the current gain should be equal to zero Ssment CE255/EE255 (O1)- Dr. Mamoun Al-Mistar Jump to...
solve a,b and c please. a. Define on-off ratio. Why series JFET has higher on-off ratio as compared to shunt JFET? b. Compare inverting and non-inverting amplifier? c. calculate the closed loop gain of the circuit diagram given below.
+Vcc Vin VI Vo Vref VN -Vcc Ry RxL Figure Q.A2(e). Inverting Schmitt-trigger circuit. (ii) The operational-amplifier (op-amp) of the inverting Schmitt-trigger in Figure Q.A2(e) has saturation voltages of +Vsat = +11 V and -Vsat = -11 V. The voltage divider circuit has the relationship of Rx = 2RY with the value of RY being 100 kn. Using the relationships derived above: (a) Calculate the values of the upper threshold point (UTP or Vi*), lower threshold point (LTP or Vr). (b) Now, sketch the input-output characteristic of the inverting Schmitt- trigger. Clearly label axes, the threshold voltages and the saturation voltages in your sketch.
Compare inverting and non-inverting amplifier. Also calculate the closed loop gain of the circuit diagram given below. 25 mv LF1S7A Vout 3 ka -15 V 150 a