t. Design the following application case 2N of is The mechanical vibration system is shown in Figure (a). When a step input with shown in Figure (b). Evaluate the values of mass m, damping constant c and spring constant k.

t. Design the following application case 2N of is The mechanical vibration system is shown in Figure (a). When a step input with shown in Figure (b). Evaluate the values of mass m, damping constant c and spring constant k.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given the vibrating system below: K1 K3 K4 Find the following 1. Keq 2. Ceq 3. Natural angular velocity K2 m C1 C3 C5 C2 C4 4. Damped angular velocity 5. Type of Damping 6. Equation of motion x(t). Assume Initial conditions for displacement and velocity Graph 2 cycles of the vibrating system. You can use third party app for this. 7. M = 10 kg K1=100 N/m K2= 80 N/m K3=75 N/m K4= 120 N/m C1 = 20Ns/m C2= 40 Ns/m C3= 35Ns/m C4= 15 Ns/m C5= 10 Ns/m
1. Suppose you are riding your bicycle on a bumpy road having a surface profile that varies harmonically with +/- 6 cm undulations. The distance between consecutive peaks of these undulations is 2 m. When you sit on the seat of your bike for your casual ride, the springs deflect 5 cm. When you are seated, the damper under the seat provides an equivalent linear viscous damping of 10% of the critical damping. A simple representation of your ride on the "never-ending" rough road is shown below. (a) If you are riding your bicycle at a horizontal speed of 2.5 m/sec, how much bumping up and down will you experience? (b) Next day, you are carrying a backpack which increases your on-seat weight by 20%. Assuming that you are still able to ride with same speed, will this "loaded" ride be more or less comfortable than your previous, "no backpack" ride? M k/23 k/2 6 cm 2 m
K Kt m₂ mi For this fig. > with damping Find the following: ~Equations of motion C ~Mass matrix ~Stiffness matrix ~Damping matrix ~Natural freqyancy ~All damping properties.. 72 ZI
6. The electro-mechanical system shown below consists of an electric motor with input voltage V which drives inertia I in the mechanical system (see torque T). Find the governing differential equations of motion for this electro-mechanical system in terms of the input voltage to the motor and output displacement y. Electrical System puthiy C V V₁ R bac (0) T bac T Motor - Motor Input Voltage - Motor Back EMF = Kbac ( - Motor Angular Velocity - Motor Output Torque = K₂ i Kbacs K₁ - Motor Constants Mechanical System M T Frictionless Support
Get the equation of motion by drawing the free body diagram of the given systems. a) Get the system's transfer function and find the unit digit answer. Show all decals in detail. m = 1 kg b= 20 Ns/m k = 125 N/m F ww k b) get the transfer function of the system. X(s)/Pg(s) =? Show all decals in detail. resistance R k Pg massless piston area (A) capacitance
O choose 1/2 dynamics model or whole- car dynamic model of the automobile O obtaion the motion differential equations of the chosen model and the equations of non-damping free vibration O calculate the natural frequencies and natural modes by Matlab program 1/2 dynamic model of the automobile parameters O% body mass M 690kg O mass moment of inertia J, = 1222kgm O wheel mass M= 40.5kg. M= 45.4kg O tire stiffness k =k, - 192000N/m O sispension stiffness ky 17000N/m. k, =2000ONim O suspension damping coefficient c c, = 1500Ns/m O geometry dimensions a= 1.25m, b= 1.51m whole-car dynamic model of the automobile Xe kater el kel lee kal te parameters O body mass m,-1380kg O mass moment of inertia of pitch 1,-2444kgm O mass moment of inertia of roll 1,-3800kgm O Viwheel distance t-0.74m O the other parameters are the same as the l/2 dynamic model
MA Figure (2) 3- The time response of a liner spring-mass-damper system with the mass of (m), the stiffness coefficient of (k), and a dampirg constant of (c) is given below in figure (2) with a set of coordinates marked by fillec circles. x(t) is in meters, it is in seconds. Indicate the units of all quantities involved in your solutions when calculate 0 -1- (0.53, 1.78) (0,0.8) 2 (2.1,-1.3) (3.7,0.9) L 4 (5.3,-0.7) - The damping ratio of the system. Its natural frequency w., damping corstart c, and stiffness coefficient k; for (m-1.25 kg). III- The amplitude of the motion if the phase angle is given as (0.4 rad). IV. Its initial conditions. (6.86, 0.5) 10 t[sec]
(2) Please write out the Equation of Movements of the following system using matrix. (Figure 2) 1 Note: Lagrange's approach is recommended. „P₂(t) ks ww P₁(t) k₁ wwm, www k₂ m₂ k6 www P3(t) k₁ k3 www m3 www Figure 2: N Degree Vibration System
A simple pendulum whose string measures 1 = 2 m and whose mass is 5 kg is at rest in its position of equilibrium and is subjected to a harmonic forcing of intensity F₁ = 2 N and frequency w rad/s. find: a) The frequency @ for which the system is in resonance. b) Make a graph of angular position v/s time where the amplitude and period of the system if the frequency w is equal to twice the resonant frequency.
Calculate the natural frequencies and vibration modes of a free-vibrating 2-GDL spring-mass system, using the matrices of this system presented below. mass matrix stiffness matrix [":] m 2k -k M K: %3D т ーk 2k
(Q-4) Balance the meter stick with two weights and a rock. 0 cm 100 cm Jrock 100g position (cm) weight (gwt) lever arm (cm) torque (gwt cm) Rock 10.60 XXXXXX XXXXXXXX Weight 1 구군, 60 150 cw Weight 2 93.5 100 (Q-5) Assume that the torques balance and use this fact to calculate the weight of the rock. Z Tecw Złcw = Wrack
A structure has a mass of 10 kip/g and a stiffness of 10 kip/in. The acceleration of gravity, g, is 386.1 in/s2. What is the value of damping assumed by the code?