The centre of gravity for the ladder (mass 10 kg)acts at point G as shown in the figure. Given thecoefficient of statics friction between the floor and the0.4 mladder is HA = 0.3 and between the wall and theladder is uR = 0.2. Find the mass of the ball, m if theladder set-up is just about to slide.0.8 mG.03 da70°Atangea adalah

Answered: Image /qna-images/answer/4fade64c-81d6-4d2b-801d-d7ebd21ac4d8.jpg

The centre of gravity for the ladder (mass = 10 kg) acts at point G as shown in the figure. Given the coefficient of statics friction between the floor and the ladder is HA = 0.3 and between the wall and the ladder is HB 0.2. Find the mass of the ball, m if the %3D ladder set-up is just about to slide.

The centre of gravity for the ladder (mass = 10 kg) acts at point G as shown in the figure. Given the coefficient of statics friction between the floor and the ladder is HA = 0.3 and between the wall and the ladder is HB 0.2. Find the mass of the ball, m if the %3D ladder set-up is just about to slide.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.35P: The weight of the cylindrical tank is negligible in comparison to the weight of water it contains...

See similar textbooks

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
Draw the FBD of the entire frame, assuming that friction and the weights of the members are negligible. How many unknowns appear on this FBD?
Find the stable equilibrium position of the system described in Prob. 10.56 if m = 2.06 kg.
The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the pressure in pounds per square inch (psi) and r represents the radial distance in inches. Determine the torque C required to operate the sander at constant speed if the kinetic coefficient of friction for the surface being sanded is 0.86.
Find the tension T in the cable when the 180-N force is applied to the pedal at E. Neglect friction and the weights of the parts.
The center of gravity of the nonhomogeneous bar AB is located at G. Find the angle at which the bar will be in equilibrium if it is free to slide on the frictionless cylindrical surface.
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
A skier starts from rest on the 39° slope at time t = 0 and is clocked at t = 2.60 s as he passes a speed checkpoint 20 m down the slope. Determine the coefficient of kinetic friction between the snow and the skis. Neglect wind resistance. 39⁰
Two bodies is connected in point C, are supported by rigid underlay at an angle α. F is the force acting on right body. We are considering the weight of bodies G and the friction between the bodies and the underlay. Length of bodies l=2000mm.    G1= 160 N, G2= 180 N, α = 30° Find:  1.) Find the magnitude of the force so that it slips on the underlay 2.) Draw the dependence of the force F as a function of the coefficient of friction f (in the range 0-0.5)