The rod supports a cylinder of mass m = 80 kg and is pinned at its end A. If it is also subjected to a couple moment of M = 500 N-m, determine the angle for the system to be in equilibrium in degrees. The spring has an unstretched length of 1 m and a stiffness of k = 600 N/m. L₁ and L2 are 1.6 m and 1.4 m, respectively. M 1 m L1 +0 m L2 k B

The rod supports a cylinder of mass m = 80 kg and is pinned at its end A. If it is also subjected to a couple moment of M = 500 N-m, determine the angle for the system to be in equilibrium in degrees. The spring has an unstretched length of 1 m and a stiffness of k = 600 N/m. L₁ and L2 are 1.6 m and 1.4 m, respectively. M 1 m L1 +0 m L2 k B

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.50P

See similar textbooks

Similar questions

Q4 / Determine the unstretched length (Lo) of spring Ac if a force P= 400 N causes the Ø=60° for equilibrium cord AB is 0.6m long . Take K=850 N/m. As shown in fig (4)? 0.6 m 0.6 m www
Question 2: The ideal spring of constant k-2.6 kN/m is attached to the disk at point A and the end fitting at point B, as shown. The spring is unstretched when OA and Oв are both zero. If the disk is rotated 15° clockwise and the end fitting is rotated 30°counterclockwise, determine the vector expression for the spring force F. Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m. - A = 15°1 A 250 mm lllllll 900 mm k = 2.6 kN/m OB = 30° B G 200 mm
Q3 - The uniform bar OC of length L and mass ( m ) pivots freely about a horizontal axis through O. If the spring of modulus k is unstretched when C is coincident with A, determine the tension T required to hold the bar in the position shown. The diameter of the small pulley at D is negligible. T L/2 45° 30° B L/2 mg A www
2. Find the horizontal force P to start the motion of any part of the system of three blocks resting upon one another as shown. The weight of the blocks are W-300 KN, Ws= 100 KN and Wc =200 KN. Between A and B μ=0.30, between C and B, μ =0.20 and between C and the ground, p=0.10. 1 sni brod nog 02.0-4 B C 05.0-4 Solution: tamos quoy worla bre sosia asquar 005 300 en of jells400 N₁-300 F3 N-300- N₂=300 Assuming B and C will not move. F₁ = 300 (0.30) F₁ = 90 kN ne à bns A zelboß 1 P = 90 kN es ensla berb hebnu 02.0- y elin 05.0= q V in Celpris orllanimetsa MX 008 Assuming C will not move: al 1st F2=400 (0.20) = 80 kN OTE Bm ribirte F₂ vica Assuming the three blocks move: F3 = 0.10 (600) F3 = 60 kN P=60 KN Least force is 60 kN.
A 415 kg safe is hanging from the apparatus below. Determine the tension in the cable. Dimension a=1.9 m and dimension b=2.5 m. The mass of the beam is 85 kg. Use g = 10 N/kg. Hint: Take torques about the hinge and use the perpendicular lever arm version of the torque equation (the sin theta version will work but will require more calculation).
The 0.6 m uniform slender bar has a mass of 5 kg. Two springs 1 and 2 having stiffness k, = 80 N/m and k₂= 45 N/m respectively are attached at end B of the slender bar. A 20 kg mass is suspended through a rope of negligible weight at the other end as shown. If a counter-clockwise moment M = 10 N. m is applied on the bar when it is at rest in the horizontal position, determine the angular velocity (₂) of the slender bar when it has rotated 30° couterclockwise. Note: Both springs always remain vertical because of the roller supports shown and are unstretched when the bar is horizontal. (Include any diagrams needed to support your solutions) 201 0 10 Km 04M A-80 N/m 45 N/m O 06m
Q3 - The uniform bar OC of length L and mass (m ) pivots freely about a horizontal axis through O. If the spring of modulus k is unstretched when C is coincident with A, determine the tension T required to hold the bar in the position shown. The diameter of the small pulley at D| is negligible. T D L/2 45° B 30 L/2 mg А wwww
1 ft 4 ft A 2 ft 45° X 5 B 3 ft Z 45° F₂ 5 ft 30° If F₁ = 300 lb. and F₂ is 250 lb., what are the reaction components on the smooth journal bearings A,B and C? Include a free body diagram of the bent pipe. F₁ lies entirely in the y-z plane.
The homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs. Motion could occur as slipping or tipping and you must decide which occurs first. Find the value of P which first causes motion. A B Answer: P = 32° P 1.5 d C mg μs = 0.43
The dimensions a = 2 m and b = 1 m. The couple M = 2400 N-m. The spring constant is k = 6000 N/m, and the spring would be unstretched if h = 0. The system is in equilibrium when h = 2 m and the beam is horizontal. Determine the force F and thereactions at A.
A rear suspension system for a front wheel-drive vehicle is shown here. Spring EF is offset behind member CD. The normal force due to contact between the wheel and the road is 4200 N. Assume the weight of the wheel and suspension system components is negligible. Determine the magnitude of the member CD. Is the member in tension or compression? Determine the support reactions at A. Determine the unstretched length of the spring EF given a spring constant of 150 kN/m.
FA BO К mm L mm- M mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. When the smooth cam C is in the position shown, determine the force on the spring FD and input its absolute value. (If your answer is negative, input its positive value such as -17 --> 17 ) Use the followings; FA=57N FC=246N K=51mm M=12mm L=22mm O=35degrees ww