The rotating shaft shown in the figure is machined from AISI 1020 CD steel. 6 kN. Find the minimum factor of safety for It is subjected to a force of F fatigue based on infinite life. If the life is not infinite, estimate the number of cycles. Be sure to check for yielding.

The rotating shaft shown in the figure is machined from AISI 1020 CD steel. 6 kN. Find the minimum factor of safety for It is subjected to a force of F fatigue based on infinite life. If the life is not infinite, estimate the number of cycles. Be sure to check for yielding.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the design in the figure, a force of Fn=45992 N acts in the vertical plane on a machine element with a diameter of D=200 mm on the shaft resting on the A and B bearings. If the angle made by this force with the horizontal is b=40o, find the life of the 6210 coded Deep Ball bearing to be used in the B bearing, in hours. Number of revolutions = 30 rpm. 1-) The diameter of the machine element on which the force acts will be taken into account in the calculation of bearing forces (That is, it will be assumed that the Fn force AFFECTS THE GROUND shown in the figure, NOT the axis of the shaft). 2-) Pi number will be taken as 3.14.
1- A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.
Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at location A to another pulley at location B. Assume the tensions In the belt at pulley Bare T, and T2, where T Is 15% of T2. NOTE: This is a multi-part questlon. Once an answer is submitted, you will be unable to return to this part. T2 10.0 18.0" Bearing at O 500 Ib 12.0 pulley diameter = 8.0" 75 Ib T1 pulley diameter = 10.0" Bearing at C Sut 163 kpsl Sy 117 kpsl Materlal 1050 Q and T Using the DE-Goodman criterla and a design factor of 1.5, calculate the diameter based on the shaft's loadings and your guess for the shaft's dlameter at the critical location. What Is the shaft diameter? Assume the notch radlus to be 0.02 In. (You must provlde an answer before moving to the next part.) The shaft dlameter Is| 1.3146| In. The factor of safety agalnst ylelding Is 3.75
A 6 mm steel wire is 5 m long and stretches 8 mm under a given load. If modulus of elasticity is 200 Gpa, find the load applied. A. 7 KN B. 8 KN C. 9 KN D. 10KN Please solve the Problem elaborately and Refer Machine Elements and Stresses Equations from the figures or use other shortcut Methods you have or you may Solve both or in more different methods the better ?. Your solution will be use as reference for my Future Board Exam preparation/review/study. Thank you so much dear your work will be appreciated much and rated excellently.
Q1: Find the Diameter of the shaft macle of A cold-drawn steel. Assume hat ultimate stress is 370 MPa and the factor of the safety is 3. For pulley A consider 250 Dia. the loose belt tension is 15 percent of the tension on the tight side. *All dimensions units are in mm. 300 Tz A 400 T₂ 50 N. 270 N. 45° 150. 300 Dia. T P x 60 2 KN T = (T₁ - T₂) Rc Tw M z 16 + T² xxx d³
B) A simply supported shaft is shown in the following Figure. A constant magnitude distributed unit load p is applied as the shaft rotates. The shaft is also subject to a steady torque of Tmax 2000-N -m., find the diameter of shaft required to obtain a safety factor of 2.5 in fatigue loading if the shaft is steel of Sut 814 MPa and Sy 703 MPa. The dimensions are in cm, the distributed force in N/cm, and the torque is in N-m. No stress concentrations are present, the shaft is machined, the required reliability is 90%, and the shaft operates at room temperature Figure: 1= 20-cm: b = 18-cm ; a = 16 cm Applied distributed load p:= 1000 N em ; 区区
Q2: A rotating steel shaft shown: camied by bearings A and E. Machined surface. S - 500 MPa, reliability is 90%, r-3 mm. What is the life of the shaft if design factor 3? 100 100 - 300 15 kN 200- A 304 3rB -3r 35 450
cylindrical pressure vessel has inside diameter d_{o} = 500 mm and inside diameter di=490 mm.if it i made of carbon steel SAE 1040 OQT1300, find the maximum allowable internal pressure if the safety factor against yielding is not to be less than 4. Neglect the external pressure and assume that the longitudinal stresses are taken by the vessel itself. a) Solve using the MSST. b) Solve using the DET. See Appendix 3 for material properties.
Two identical shafts one made of steel (Gst = 75 GPa) and the other is made of aluminum (G = 25 GPa), Al are acted by same torque. Then Select one: O a. The shear stress in steel shaft is three times larger than in aluminum shaft. O b. The shear stress in aluminum shaft is same as in steel shaft. O c. The shear stress in aluminum shaft is three times larger than in steel shaft. O d. The shear stress in steel shaft is 1.5 times larger than in aluminum shaft.
The head of a 300 mm diameter cylinder vessel will be designed. The internal pressure in the cylinder is Pin = 1MPA. The bolts have initial tightening load of 12 kN. a) Find the stiffness of the bolt and members. b) Determine the number of bolts (N) for a safety factor of 2 for fatique loading. IMPA D= 300 mm M 10 1.5 grade 5.8 cast iron E= 200 GPa Eci= 90 GPa
03: A shaft carrying three loaded pulleys with stepped diameters as shown. The modulus of rigidity for the shaft is (G-28GPA) and the shaft segments have the same lengths 48N.m (AB-BC-CD-30Cm). Determinc the following: GON.m 144N,m 1- Maximum shearing stress in the shaft CD. 2- The angle of twist of the pulley A relative to B.
A hollow circular shaft with OD 1.5 and ID 1.25 and made of steel with an allowable shear stress of 15 ksi is rated for 5000 in-lbs of torque. A narrow slit is cut lengthwise along the shaft as shown in the figure on the right. Determine the rated capacity of the shaft after it has been modified. Choose the answer that is closest from the list below. 0 0 0 0 3,600 in lbs 360 in-lbs 1,800 in-lbs 2,500 in-lbs