The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa. Neglecting the effect of stressconcentrations, determine the smallest diameters dAB and dBc for which the allowable shearing stress is not exceeded. Take Tc=420 N-m.TB=1200 N.mTCdak750 mmB\decC600 mmThe smallest diameter dдBisThe smallest diameter dBc ismm.mm.

if you have any doubts please comment

Answered: The solid shaft shown is formed of a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid steel shaft AB, shown in Fig. is to be used to transmit 5 hp fromthe motor M to which it is attached. If the shaft rotates at v = 175 rpm andthe steel has allowable shear stress of tallow = 14.5 ksi, determine therequired diameter of the shaft to the nearest 18 in.
A solid shaft consisting of steel and aluminum segments carries the torques T and 2T. Find the largest allowable value of T if the working shear stress is 14,000 psi for steel and 7,500 psi for aluminum, and the angle of rotation at the free end must not exceed 8 degrees. Use G = 12 x 10^6 psi for steel and G =4 x 10^6 psi for aluminum. Express your final answer in Ib.ft to the nearest whole number. Note: Do not include the unit in your answer. 27 2 in. 1.5 in. 3 ft B 2 ft |C 800mm 500mm
A torque of TD= 1235 N-m is applied to gear Dof the gear train shown. The bearings shown allow the shafts to rotate freely. Assume shafts (1) and (2) are solid 26-mm-diameter steel shafts. Determine the magnitude of the maximum shear stress acting in shaft (2). 230-mm dia. TD C B 150-mm dia. O 357.9 MPa O 449.0 MPa O 415.7 MPa O 217.5 MPa O 391.8 MPa
1. A drive shaft to the blades of a helicopter transmits 800 kW at 200 rev/min. Neglecting transmission losses; determine the minimum external and internal diameters of the hollow circular section aluminum alloy shaft, when the maximum permissible shear stress in the shaft is limited to 30 MPa. It may be assumed that the external diameter of this shaft is twice its internal diameter. What will be the resulting angle of twist of this shaft over a length of 2 m, given that the modulus of rigidity, C 26900MPA.
A1 m long and 35 mm diameter aluminum shaft is to be replaced by a steel hollow shaft of the same length and the same outside diameter. It is required to design the steel shaft to withstand double the shear stress that of aluminum shaft. Determine the inside diameter of the stee I shaft. Find the values of the shear stresses on each shaft if a torque of 3 kN.m is applied to both of d=20mm them.
a. Determine the maximum shear stress at segment AB (in MPa) b. Determine the maximum shear stress at segment BC (in MPa) c. Determine the maximum shear stress at segment CD (in MPa) d. Determine the angle twist of Gear D relative to A (in degrees) note : indicate free body diagram
Illustrate and completely solve the problem! Write legibly or type written the solutions. The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass core 0.5 in. in diameter. If a torque of 250 lb-ft is applied at its end, determine the maximum shear stress in psi experienced by the assembly. Take G for steel at 11.4 x 103 ksi and G brass at 5.2 x 103 ksi.
A flange coupling is to be designed, using 6 bolts at a distance of 149mm from thecenter of the shaft, allowable shearing stress on the bolt is 103 MPa. If the shaft is totransmit 5485 hp at a speed of 1200 rpm, (a) determine the bolt diameter required inmm. (b) If the shaft is made of the same material as the bolt, determine the requireddiameter of the shaft in mm.
A rectangular key was used in a pulley connected to a shaft witha power of 125 kW at a speed of 900 rpm. If the shearing stressof the shaft is 40 MPa and the key to be 22 MPa. Determine thelength of the rectangular key if the width is one fourth that ofthe shaft diameter.
A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12ksi. IF the diameter of the shaft is 1.5 inches diameter the maximum torque T if a 1in, diameter hole is bored through the shaft? Sketch the shear stress distribution along a trial line in each case.
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter doof the solid shaft.g The required outer diameter d2of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. 3.The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
A solid shaft has an allowable shear stress of 37 MPa and transmits a torque of 1236 Nm. Determine the minimum diameter of the shaft in mm (give answer correct to 2 decimal places).

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS