What standard PG asphalt binder grade should be selected under the following conditions: a. The seven-day maximum pavement temperature has a mean of 62°C and a minimum pavement temperature of -15°C. (table9.2) b. According to part a, what is your recommendation for 20 million ESALs and 50 km/h speed? (table ESALs) c. For 50 million ESALs and 80 km/h speed. (table ESALs)

What standard PG asphalt binder grade should be selected under the following conditions: a. The seven-day maximum pavement temperature has a mean of 62°C and a minimum pavement temperature of -15°C. (table9.2) b. According to part a, what is your recommendation for 20 million ESALs and 50 km/h speed? (table ESALs) c. For 50 million ESALs and 80 km/h speed. (table ESALs)

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter2: Atoms, Chemical Bonding, Material Structure, And Physical Properties

Section: Chapter Questions

Problem 41CQ

See similar textbooks

Similar questions

do not round off in between solution
I In a compression test and for a very ductile material similar to copper , the diameter and the length of the specimen before the test were 60mm and 80mm respectively . Find the length , in inches , after the test if the diameter became 120mm . Assume that the density remained unchanged
Determine the force in each member of the loaded truss. All triangles are equilateral with side length d. The forces are positive if in tension, negative if in compression. AB= tolerance is ± 1 in the 3rd ficant digit. AG = BC = BG= CD = CF = i i i i i B i G 2.8 KN d F 6.3 KN 3 3 3 3 3 3 KN KN KN kN kN D E
d) Calculate total hardness in ppm of a solution of both 55 mg/L Al2(SO4)3 and 45 mg/L Mg(NO3)2.
When the exponential trend line of iron concentration vs time is y=4.2 exp(-0.24x) x is time in min and y is concentration of phen iron complex solution.
Q) When Plastic viscosity is increase ? small solid concentration Concentration solid Increases solid concentration Decrease solid concentration Irregular solid concentration
Using the isothermal transformation diagram for a 0.45 wt% C steel alloy (Figure 10.40), determine the final microstructure (in terms of just the microconstituents present) AND approximate percentages of the microconstituents that form in a small specimen that has been subjected to the following time-temperature treatments. In each case assume that the specimen begins at 845°C (1550°F), and that it has been held at this temperature long enough to have achieved a complete and homogeneous austenitic structure. (a) Rapidly cool to 250°C (480°F), hold for 10^3 s, then quench to room temperature. (b) Rapidly cool to 700°C (1290°F), hold for 30 s, then quench to room temperature. (c) Rapidly cool to 700°C (1290°F), hold at this temperature for 10^5 s, then quench to room temperature. (d) Rapidly cool to 400°C (750°F), hold for 500 s, then quench to room temperature.
cmplete solution
Q4/ A. Explain why ceramic materials do not response to the plastic deformation processes? Also clarify why flexural test is applied to ceramics instead of tensile test? B. Estimate whether a cylindrical aluminum oxide sample will fail or not when it subject to flexural test to achieve flexural strength of 390 MPa knowing that the sample radius is 2.5 mm, separation distance is 30 mm, and the applied load is 620 N respectively.
Answer by true or false for the following The impurities in mixing water improve the durability. a- True b- False
choose True OR false Q1A- Secant modulus is given by the slope of a line drawn between two points on the stress-strain curve. * True False B- Carbonation shrinkage occurs due to excessive fall in temperature * True False C- A poorer paste structure undergoes a higher creep. * True False
•Sam, the strawberry producer, has had complaints from the produce company that his strawberries are damaged during transit. Sam would like to know the force required to damage the strawberries if they are stacked three deep in their container. •The damage occurs on the bottom layer at the interface with the parallel surface of the container and also at the point of contact between the layers of strawberries. •An hydrostatic bulk compression test on a sample of Sam's strawberries indicates an average bulk modulus of 225 psi. Testing of specimens from Sam's strawberry crop shows a compression modulus E of 200 psi. The average strawberry diameter is 1.25 inches and the axial deformation due to the damage in transit averages 0.23 inches. The modulus of elasticity for Sam's variety of strawberries is reported to be 130 psi. •Estimate the force Sam's strawberries may be encountering during transit. (Hertz method)