You find that for your analysis, your response factor (adjusted for internal standard) for a particular analyte was 0.0104 ppm. When you run a sample mixture, the integration for that component is 2,186, and the integration for the internal standard is 14,139. What is the concentration of the component in ppm? (Enter the numerical value without units.)

You find that for your analysis, your response factor (adjusted for internal standard) for a particular analyte was 0.0104 ppm. When you run a sample mixture, the integration for that component is 2,186, and the integration for the internal standard is 14,139. What is the concentration of the component in ppm? (Enter the numerical value without units.)

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter7: Statistical Data Treatment And Evaluation

Section: Chapter Questions

Problem 7.26QAP

See similar textbooks

Similar questions

SCE students measured the concentration of HCl in a solution by titrating with different indicators to find the end point.Indicator Mean HCl concentration (M)(± standard deviation)Number of measurementsBromothymol blue 0.09565 ± 0.00225 28Methyl red 0.08686 ± 0.00098 18Bromocresol green 0.08641 ± 0.00113 29Is the difference between indicators 1 and 2 significant at the 95% confidence level? Answer the same question for indicators 2 and 3
Calculate the gravimetric factor of the following. 2 Fe3O4 is sought(Analyte), 3 Fe2O3 is weighed (Precipitate)
Gravimetric determination of Ksp. Table 1 Trial Volume of solution used (ml) Mass of empty beaker (g) Mass of beaker with solid residue (g) Mass Ca(OH)2 (g) Ksp for Ca(OH)₂= % error = 10mL 92.808g 92.766g 0.042g Determine the mass of dissolved solid that was in the saturated solution. Calculate the molar solubility of the solution (M) using the mass of dissolved solid, the volume of solution used in the analysis, and the molar mass of calcium hydroxide. Substitute the molar solubility into a version of equation 4.1 [Hint: use an ICE table] to determine the Kp. Provide an annotated calculation below: 1
grammarly-G X * Content oard.odu.edu/ultra/courses/_393452_1/cl/outline F2 Question Completion Status: X GA student wan X 1 QUESTION 3 A student wants to determine the solubility of water and copper (1) bromide (a green solid) in ethyl acetate (a colorless organic liquid). She places 1 mL of ethyl acetate into each of two test tubes. To one, she adds 5 drops of water to it. To the other, she adds a small scoop of copper(1) bromide. 8.0 F3 2 - Which test tube represents the ethyl acetate and A. Test tube 1 copper(1) bromide if the copper(1) bromide is insoluble in ethyl B. Test tube 2 acetate? C. Test tube 3 D. Test tube 4 - Which test tube represents the mixture of the ethyl acetate and water if the water is insoluble in ethyl acetate? $ Question Com X C Chegg Search x 3 Which test tube represents the mixture of the ethyl acetate and water if the water is soluble in ethyl acetate? - Which test tube represents the ethyl acetate and copper(1) bromide if the copper(1) bromide is soluble…
The scatter plot below shows the density of ethylene glycol solutions vs. the mass % of those solutions. Density (g/mL) 1.04+ 1.03- 1.02- 1.01 0.99- 0.98- 8 % 10 12 14 16 18 20 Mass % Q The equation for the line of best fit shown on the scatter plot is y= 0.001683 +0.9959. Use the equation of the trendline to determine the mass percent of an ethylene glycol solution with a density of 1.015 g/mL.
Compute for the numerical value of the gravimetric factor required to convert the given precipitate into the desired analyte. 1. Magnesium ammonium phosphate (MgNH4PO4) precipitate into phosphorous (as diphosphorous pentoxide, P2O5). 2. Magnesium ammonium phosphate hexahydrate (MgNH4PO4.6H2O) precipitate into nitrogen.
Calculate the mass percent of the ascorbic acid in the same show full solution Situation: The pounded Vitamin C tablet was half into two below are the calculated data in the experiment. Each of the half are transfered in a 250ml erlen meyer flask and added 75ml of deionized water for the vitamin C to dissolve. Then it was prepared for titration where the burette was filled with 0.09794M standardize NaOH solution then a total of with 3 drops 2% phenolphthalein indicator was added to each erlen meyer flask l, swrill it and begin the titration. below are the following data gathered: Vitamins used: Nature Made vitamin C 500mg tablet Trial 1 Mass: 0.3108g of Vitamin C tablet Initial volume: 1.6mL Final volume: 15.4mL Trial 2 Mass: 0.3349g Initial volume: 15.4 mL Final volume: 30.2 mL
The following data were collected for the reaction 2A + 2B + C 3G+ 4 F Experiment 2 3 4 5 [A] Units of Molarity .00125 .00250 .00125 .00125 .00301 [B] Units of Molarity 00125 .00125 00302 00302 .00100 [C] Units of Molarity 00125 .00125 .00125 00375 .00115 Rate Units M/s 00870 .0174 .0508 .457 a. What is the order with respect to each reactant and what is the overall order for the reaction? Answer this question within the answer box and show your work clearly labeled on the scratch paper. b. Write the rate law for the reaction. Answer this question within the answer box and show your work clearly labeled on the scratch paper. c. What is the value and units for k? Answer this question within the answer box and show your work clearly labeled on the scratch paper. d. Predict the rate for experiment 5, you should give a value and units. Answer this question in the answer box and show your work on the scratch paper labeled clearly.
The standard addition method is used to analyze a sample of a river water for mercury. Solution A is made by pipetting 5.00 mL of undiluted sample in to a 10 mL volumetric flask and filling to the mark with DI water. Solution B is made by pipetting 5.00 mL of undiluted sample and 3.00 mL of 15.0 ppb of Hg standard into same 10.0 mL volumetric flask and filling to the mark with DI. Solution A and B are analyzed using atomic absorption spectroscopy and give a percent transmittance values of 56 % and 33 % respectively (not blank corrected). A blank has a transmittance of 96%. What is the corrected absorbance of both solution A and B? OA. Solution A: 0.123 Solution B: 0.463 O B. Solution A: 0.463 Solution B: 0.234 O C. Solution A: 0.123 Solution B: 0.234 O D. Solution A: 0.234 Solution B: 0.463
The standard addition method is used to analyze a sample of a river water for mercury. Solution A is made by pipetting 5.00 mL of undiluted sample in to a 10 mL volumetric flask and filling to the mark with DI water. Solution B is made by pipetting 5.00 mL of undiluted sample and 3.00 mL of 15.0 ppb of Hg standard into same 10.0 mL volumetric flask and filling to the mark with DI. Solution A and B are analyzed using atomic absorption spectroscopy and give a percent transmittance values of 56 % and 33 % respectively (not blank corrected). A blank has a transmittance of 96%. What is the corrected absorbance of both solution A and B? A. Solution A: 0.123 Solution B: 0.463 B. Solution A: 0.463 Solution B: 0.234 C. Solution A: 0.123 Solution B: 0.234 D. Solution A: 0.234 Solution B: 0.463
Mass of Sample Volume of KMnO, solution used in titration Equivalents of permanganate used Equivalents of iron (II) in sample Moles of iron (II) in sample Grams of Iron in Sample % Iron in Sample Average % Iron in Unknown Instructor's Grade for Precision in Part B. Sample Calculations Part B: 0.58179 0.68719 28.19 ml 31,96m6 007662 00266 2 11 n
Calculate the gravimetric factor of the following. 2 Fe3O4 is sought(Analyte), 3 Fe2O3 is weighed (Precipitate) 2 Fe is sought(Analyte), 1Fe2O3 is weighed (Precipitate)