1. All plates A-D shown in the figure below move rigidly without rotation. All ridges add at equal rates to the plates on either side of them (the rates given on the diagram are half the plate- separation rates. The trench forming the boundary of plate A does not consume A. Use the plate velocities and directions to determine (a) the relative motion between plates B and D (b) the relative motion between the triple junction J and plate A. Where and when will J reach the trench? Draw a sketch of the geometry after this collision showing the relative velocity vectors and discuss the subsequent evolution

1. All plates A-D shown in the figure below move rigidly without rotation. All ridges add at equal rates to the plates on either side of them (the rates given on the diagram are half the plate- separation rates. The trench forming the boundary of plate A does not consume A. Use the plate velocities and directions to determine (a) the relative motion between plates B and D (b) the relative motion between the triple junction J and plate A. Where and when will J reach the trench? Draw a sketch of the geometry after this collision showing the relative velocity vectors and discuss the subsequent evolution

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4) A large moveable plate is located between two large plate as shown in the figure. Determine the magnitude and direction of the shearing stresses that act on the fixed walls when the moving plate has a velocity of 4 m/s. Assume that the velocity distribution between the plates is linear Fixed plate 6 mm H- 0.02 N. sim 4 m/s 3 mm A = 0.01 N• sim Fixed plate
is 0.25 m². Find: i) Фy and w, The power required to keep the plate in steady motion ii) PROBLEM 7 The velocity distribution in a pipe of radius ro is given by: m Annular when m<1 Ring Vm Find the momentum correction factor B +dr ro PROBLEM 8 Viscous (laminar) of oil takes place down the slope between parallel plates, 8mm apart, held inclined at 30° to the horizontal. The oil of viscosity 0.92 kg/ms and of mass density 1320 kg/m³. The pressure of two points, Im vertically apart, are 40KN/m² and 170 kN/m², when the upper plates moves at 0.3 m/s . velocity relative to the lower plate in the direction opposite to the oil flow. Determine: i) ii) iii) Maximum velocity of the flow within the oil medium The shear stress on the top plate The rate of oil flow per metre width 170 kN/m? 40 kN/m? U = 0.3 ms-1 Upper Plate 1m 8 mm (Datum) Direction of oil flow Lower Plate 30 PROBLEM 9 A siphon has rectangular throat section 2.2 m wide and the radius of the crown and crest ara 3m and 1.6m…
The cross-sectional area shown is subjected to V-600 kN and M -1000 kN-m. What is the transverse shear stress just below point B? (in MPa) 100 mm 100 mm 100 mm 100 mm 100 mm B 100 mm
Determine the magnitude and direction of the resultant of forces acting on the plate shown in figure below A-10 KN B=32 KN 000 GUSSET PLATE Co0° C=8KN
Q.5 The velocity distribution for flow over a plate is given by U=2y-y² in which u is the velocity in ms¹ at a distance y metres from the plate. Determine the shear stress in Nm-2 at the boundary and at 0.2 m from it. Dynamic viscosity of fluid is 0.9 Ns/m².
A 100 mm diameter hole is bored a distance h into the base of thecone of density 5 Mg/m3. The cone is 500 mm tall with a radius of 150 mm at it’s base.Determine:(a) the centre of mass of the cone without the cylindrical bore-hole (i.e., a solid cone),(b) the centre of mass of the cone with a cylinder of height 50 mm bored into thebase of the cone. (Note this question is slightly different than the normal text book hibbler statics question)
1.6 The space between two parallel plates kept 3 mm apart is filled with an oil of dynamic viscosity 0.2 Pa.s. What is the shear stress on the lower fixed plate, if the upper one is moved with a velocity of 1.50 m/s? (Refer Fig. 1.3). 3 cm Fig. 1.3
The lower plate is stationary, the upper plate moves at a velocity of 10 ft/s. Oil (SAE 10W-30, 150 °F) which fills the space. The variation in velocity of the oil is linear. What is the shear stress in the oil? : Two plates are separated by 1/4 inch
determine the absolute maximum bending stress in the beam, and (3) determine the magnitude of the developed bending stress at any arbitrary point (betweent the neutral axis and the farthest point on the beam's cross section). Show the results acting on volume elements located at these points. 200 mm 50 kN/m 50 kN/m 20 mm 300 mm 20 mm 20 mm -4.5 m - 4.5 m
Two horizontal plates are placed 2 cm apart, the space between them being filled with oil of viscosity 1.6 Ns/m² The bottom plate is stationary. What is the shear stress in oil if the upper plate is moved with a velocity of 2 m/s? 3
Steel bars and an aluminum bar support the rigid slab as a platform as shown below. A gap A= 0.26 mm exists between the aluminum bar and the slab. Neglecting the weight of the slab a (/degree celsius) 11.6х106 23.1x106 A (mm²) Steel bar Aluminum bar E (GPa) 200 70 350 400 a) Which temperature increase AT is required to just close the spacing at the middle? (Note that the temperature increase will subject all bars) b) What are the stresses in the steel bars and aluminum bar for AT = 90 degree celsius in MPa? 1000 mm Steel Aluminum Steel
Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when P = 100lb. 50 lb H, = 0.40 Hi = 0.30 40° 30° O Block is in Equilibrium, F-43.032 Ib, 30 deg. with the Harizantal Axis O Block is in Equilibrium, F-32.274 b, 40 deg. with the Harizontal Axis O Block is not in Equilibrium, F-32.274 lb, 30 deg. with the Horizontal Axis O Block is in Equilibrium, F-32.274 b, 30 deg. with the Horizontal Avis O Block is not in Equilibrium, F-43.032 lb, 30 deg, with the Horizontal Axis