Show all work please be neat 5- Following data are given for a direct shear test conducted on dry sand:smuaz Specimendimensions:60mm x 60 mmx 20 mm(height)Normal stress: 100 kN/m2Shear force at failure:200 NDetermine the angle of friction?

Given Normal stress = 100 KN /m2 Shear force at failure= 200 N

5- Following data are given for a direct shear test conducted on dry sand: Specimendimensions:60mm x 60 mmx 20 mm(height) • Normal stress: 100 kN/m2 • Shear force at failure:200 N NE=V Determine the angle of friction?

5- Following data are given for a direct shear test conducted on dry sand: Specimendimensions:60mm x 60 mmx 20 mm(height) • Normal stress: 100 kN/m2 • Shear force at failure:200 N NE=V Determine the angle of friction?

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter3: Natural Soil Deposits And Subsoil Exploration

Section: Chapter Questions

Problem 3.29P

See similar textbooks

Related questions

Q: QUESTION 1 Solve MOMENT DISTRIBUTION METHOD tabulation with the shear diagram and the moment diagram…

A: To draw the Shear and Moment diagram for the continuous beam.

Q: A 2.8 m square column fooring has a total thickness of 47 mm. The factored moment at critical…

A: A) Given data : Square column = 2.8 m Total thickness = 47 mm Factored moment = 640 kN-m f'c = 21…

Q: HW 1. At a given location, the space mean speed is measured as 40 mi/h and the rate of flow as 1,600…

Q: AZIMUTH 1. Convert N 45 36' E to its equivalent azimuths 2. Convert S 65 15' E to its equivalent…

Q: te: Complete solution with figures. Express your intermediate answers with at least FOUR decimal…

A: A beam is given with roller supports at A and D and a hinge support at F. The beam also has a member…

Q: Determine the increase of pore water pressure at M due to the infinite strip loading shown in Figure…

Q: A theodolite has a tachometric constant of 100and an additive of zero. the center reading on the…

Q: Problem 4 A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water…

A: Given data in question Pressure 250 kPa (abs) Atmospheric pressure 100 kPa Depth 2.5 m Diameter 10…

Q: an accumulation test is used to determine: a) evaporation rate b) furnace volume c) how…

A: Objective: To choose the correct option corresponding to accumulation test. Given statement: An…

Q: Problem 1. A force of 675 lb is directed from E toward F in the cube shown in Fig. 3-C. Determine…

A: Given: 675 lb force is directed along E to F Required: Moment of force about each of the coordinate…

Q: Using the slope-deflection equations, (a) determine the end moments of members AB, BC, and BD, (b)…

A: To determine Moment at AB, BD, DB Rotation at A and C

Q: A seawater sample has a chlorinity of 2.8 percent. Calculate its salinity in parts-per-thousand…

A: This question is related to the Environmental Engineering from Civil Engineering. In this question…

Q: In order to compute the airport reference temperature and the standard temperature with respect to…

A: Given that :- Monthly mean of maximum daily temperature = Tm=41.5° C Monthly mean of average daily…

Q: INSTRUCTIONS 1) Consider clockwise moment is positive and counterclockwise moment is negative. 2)…

Q: Show a complete solution. Classify each of the structures as statically determinate or…

A: To classify the each structure-

Q: If you are the designer in this case, when the beam is an indeterminate structure, would you…

A: Given beam is indeterminate,as a designer can we recommend plastic design-

Q: 13. A soil has a specific gravity of solids (Gs) of 2.65, a water content of 13% and a void ratio of…

A: Porosity: Porosity is the measure of the void space in the material. The amount of void space is…

Q: Q1] The precast floor system consists of a 150-mm-thick concrete slab carry its self weight as well…

Q: The average rainfall values over a catchment in three successive 2-hour intervals are 3, 5 and 2 cm,…

Q: axially loaded column. Determine the allowa ssive load using Euler's formula and a factor c e column…

Q: Problem 3. Draw the shear and Bending Moment Diagram of the beam shown. Solve the problem using…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the…

A: Given: The head indicated by two piezometers P and Q are 55.2 m and 34.1 m. The aquifer has a…

Q: As shown in the figure, a pump draws water from reservoir A (El 10m) and lifts it to reservoir B (El…

A: Given two reservoir problem with a pump supplying head. In order to calculate the pressure head at…

Q: At what advection velocity does a pulse of dissolved benzene move through organic-rich wetland soil…

A: The given data is shown below: q=0.001 cm/secPorosity=0.4Retardation factor=4.6

Q: fc' = 21 mpa fy= 280 mpa Load: 2900 Live load = 2900 Pa Weight of RC = 2400 kg/m³ Weight of CHB =…

A: f'c=21 mPafy=280 mPaWeight of RC=2400 kg/m3Column section=0.4m x 0.4mP=540000 NPu=695000 Nqa=100 kPa…

Q: 15. Shown below is a set of effluent BOD data from a treatment plant. The plant's permit requires…

Q: Determine the moment of inertia of the composite figure about an axis through its centroid and…

A: To find the Moment of Inertia of the area about the centroidal axis parallel to the base

Q: Using NSCP 2015 and Fy = 50ksi, determine the fcPn and Pn /Qc for the column shown. L C10X15.3 W8X24…

A: The given data is shown below: Fy=50 ksiC10×15.3W8×24KL=12 ft

Q: A W14 x 53 Column has an effective length for x-axis buckling equal to 20 ft. Determine the…

A: The given data is shown below: W14×53Le-x axis=20 ftAg=15.6 in.2Ixx=541 in.4Iyy=57.7 in.4

Q: A loader operating at 107 cy/hr has 2.5-cy heaped capacity bucket and has a 1.2-min load cycle. The…

Q: (a) Write the structural motion equation under earthquake excitation, and then determine the…

A: m1=m2=10,000 kgk1=k2=12(106) N/mc1=c2=1.5(104) Nsec/m Circular frequency and mode shape for the…

Q: Are load combinations an example of superposition? O True False Load Combinations The following…

A: Dead Load: The self-weight of the structure is the load of the structure which remains constant over…

Q: Match the following desired outcomes to tasks for aggregate production. Outcomes Size…

A: Reference : Building materials. Given : Different tasks are established. The exact same meaning…

Q: 4.0 m 1.50 kN/m

Q: For a culturable command area of 800 hectare with intensity of 75%, the duty on the field for a…

A: Given data- CCA=800 ha, Intensity I=75%, Duty D=1000 ha/cumec, To Find- The design discharge Q.

Q: Find the value of Elō midway between the supports for the beam shown. Use the Super Position method.…

Q: Seatwork 21 Find (a) Ix fig- shown. Ans. in 2 dic. places. 150 mm (1) Iy mmt for the composite…

A: Moment of Inertia: The moment of inertia determines the resistance of the object to the rotational…

Q: Question 2 A rectangular footing 1 m x 2 m is placed at a depth of 2 m in a saturated clay behaving…

A: Given- Rectangular footing dimension = 1 m x 2 m, Depth df = 2 m in a saturated clay, Unconfined…

Q: Determine the weight W that balances the 10-lb load placed linkage shown. on the

A: To determine the weight w, such that it balances the 10 lbs load.

Q: If the unsupported length of a stanchion is 4 meters and least radius of gyration of its cross…

A: Given, Unsupported length of stanchion = 400 cm Least radius of gyration of its cross section = 5cm

Q: Determine the horizontal and vertical at joint C using the virtual work method.

Q: Problem 1. Draw the shear and Bending Moment Diagram of the beam shown. Use the Method of…

A: Given Data Find the support reaction using superposition method and draw shear force and bending…

Q: The structure consists of two identical bars joined by a pin at B. Neglecting the weights of the…

A: To determine: The magnitude of the pin reaction at C. Given Data: The structure given consist of two…

Q: Assume a 1.4 tt, 6-8.8 ft, c-17.6ft, w-1200 lbft, and P-2800 lb. By=[ a Determine the vertical…

A: Determine the support reactions Shear at B left Shear at B right Moment at C Shear at C left Shear…

Q: Draw the shear and moment diagrams of the loaded beam shown below. Draw the diagrams V1 = -1100 kN…

A: Objective: To draw the shear and moment diagrams for the given beam. The shear and moment diagrams…

Q: Draw the influence diagram for reactions at A and B. Also draw the inluence diagram for shear and…

A: Using Muller Breslau principle ILD for reaction at support we give a unit displacement at the…

Q: 60 kN 200 kN.m O-B 12 kN/m Ic

Q: Ellaborate on the importance/ effect of forces (tension, compression and shearing) on structural…

A: Structural Members: The structural members undergo the loading which resists the load on the…

Q: To hang a statue with a mass of 102.06kg, you will be using a slender cable made of a steel alloy. A…

A: Note : As per guidelines, I will solve first 3 parts of the question. Mass of statue= 102.06 kg =…

Q: In a welded plate girder, the web plate connected to flange along both the longitudinal edges. The…

A: Given- Welded plate girder, Fe 410 grade steel, serviceability criteria for un-stiffened plate…

Concept explainers

Test for Determination of Shear Strength

The term shear strength is often associated with the soil. Shear strength is defined as the resistance to the deformation of soil particles due to the continuous action of shear stress. In short, shear strength is the maximum shear stress that a soil can sustain.

Question

Show all work please be neat

5- Following data are given for a direct shear test conducted on dry sand:
smuaz Specimendimensions:60mm x 60 mmx 20 mm(height)
Normal stress: 100 kN/m2
Shear force at failure:200 N
Determine the angle of friction?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Test for determination of shear strength

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A sand sample is subjected to direct shear testing. Two tests areperformed. For test 1, The sample shears at a stress of 2500 psf whenthe normal stress is 4000 psf.Test 2, The sample shears at a stress of 3500 psf when the normalstress is 6000 psf. Determine the following:a) Angle of Internal frictionb) Value of cohesionc) Compute the shear stress at a depth of 12 ft. if the unit weight ofthe soil is 150 pcf
The table shows the results of a consolidated undrained (CU) test on a overconsolidated clay soil sample. Sample No Cell Pressure (kPa) Deviator stress at failure (kPa) Pore water pressure at failure (kPa) 1 15 20 10 2 30 25 15 For the given data, plot the effective stress Mohr's circles at failure. Estimate the effective shear strength parameters C' amd phi'.
Triaxial tests performed on samples of aeolin sand. The failure conditions in terms of effective stress are (ov, 0h) = (515, 100), (1250, 200), (3500, 400), and (5325, 800) kPa. Using (s, t) space, determine the cohesion and friction angle. What is the orientation of the major principal stress with respect to the failure plane? Determine this graphically.
A sample of dry sand is tested in direct shear. Theshear box holding the sample has a circular crosssection with a diameter of 50 mm. The normal(compressive) load imposed is 200 N. The sam-ple shears when the shear force is 130 N.(a) Determine the test normal stress and shearstress at failure.(b) Determine the angle of internal frictionfor this soil.(c) What is the probable condition of the testedsample (dense, loose, etc.)?
A sand sample was used in a direct shear test for two trials. The first trial obtained a normal stress of 4000 psf when the shear stress at failure is 3000 psf. For the second trial, the normal stress is 6000 psf when shear stress at failure is 4000 psf. • Determine the angle of internal friction• Determine the value of apparent cohesion• Shear stress 15ft beneath the surface (psf) if the soil unit weight is 150 pcf• Major and minor principal stresses (psf)Final answer(s) should be in 3 decimal places.
Can TRIAXIAL TESTS be performed on sand samples? Briefly explain. The results of an undrained triaxial test on a clay soil sample are given in table below Cell Pressure (kN/m2) 200 400 600 Additional Axial Load at Failure (N) 342 388 465 Each sample, originally 76mm long and 38mm in diameter, experienced a vertical deformation of 5.1mm. Evaluate the stress at failure for each cell pressure given in table above. Draw Mohr Circles and determine the shear strength parameters of the soil.
2. A series of consolidated, undrained triaxial tests were carried out on specimens of a saturated clay under no backpressure. The test data at failure are summarized: Confining Pressure (kPa) Deviator Stress (kPa) Pore Water Pressure (kPa) 150 192 80 300 341 154 450 504 222 a. Draw the Mohr circles and find the cohesion and friction angles in terms of effective stresses. b. Compute Skempton’s A-parameter at failure for all three specimens. c. Is the soil normally consolidated or overconsolidated? Why? d. Another specimen of the same clay that was consolidated under a cell pressure of 250 kPa was subjected to a consolidated, drained triaxial test. What would be the deviator stress at failure?
Q # 3. Following data are given for a direct shear test conducted on dry sand: Specimen dimensions: 63 mm x63 mm and 25 mm (height). Normal stress: 105 kN/m?. Shear force at failure: 300 N a. Determine the angle of friction, for a normal stress of 180 kN/m?. b. What shear force is required to cause failure?
For a dry sand specimen in a direct shear test box, the following are given: • Angle of friction: 38° • Size of specimen: 2 in. X 2 in. X 1.2 in. (height) • Normal stress: 20 lb/in.? Determine the shear force required to cause failure.
Assume that both a triaxial shear test and a direct shear test are to be performed on a sample of dry sand. When the triaxial shear test is performed, the specimen fails when the major and minor principal stresses are 80 and 20 lbs/in^2, respectively. When the direct shear test is performed, what shear strength can be expected if the normal stress is 4000 lbs/ft^2? Show all work.
A sand sample is subjected to direct shear testing at it's (in - situ) water content. Two tests are performed. For one of the tests, the sample shears at a stress of 400 kPa when the normal stress is 600 kPa. From these data,Determine the value of the apparent cohesion. Determine the corresponding angle of internal friction.
Two undrained triaxial tests were conducted on soil specimen, and they gave the following results: Sample Confining Pressure Deviator Stress A 350 kN/m² B 500 kN/m² 150 kN/m² 300 kN/m² The shear strength of sample A in the plane of it's normal stress is A 588 kPa B 283 kPa C 730 kPa D 165 kPa Correct Option