1) Drawing: Consider a cylindrical rod fabricated from a linear strain hardening material with a constitutive relationship of a=2000 + 20000 € (where o is in psi). The rod is drawn into a wire. If the original diameter of the rod is 0.75 in, what is the minimum possible diameter that can be drawn in the first pass? Assume that redundant work is 20% of the ideal work and that the frictional work is 15% of the ideal work of deformation. What is the drawing force required to complete this operation?

1) Drawing: Consider a cylindrical rod fabricated from a linear strain hardening material with a constitutive relationship of a=2000 + 20000 € (where o is in psi). The rod is drawn into a wire. If the original diameter of the rod is 0.75 in, what is the minimum possible diameter that can be drawn in the first pass? Assume that redundant work is 20% of the ideal work and that the frictional work is 15% of the ideal work of deformation. What is the drawing force required to complete this operation?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A compression test is performed on a 2” diameter by 5” long bar of an unknown metal. At the end of the compression test, the bar has a height of 3.5 inches. The strength coefficient (K) and the work hardening coefficient (n ) are 250 MPa and 0.4, respectively. State all assumptions needed to work the problem. a) Calculate the final diameter of the bar in inches. b) Calculate the flow stress in MPa when the length of the bar is 4”.
A 250 mm diameter circle is etched on a 400 mm x 400 mm x 12 mm piece of sheet metal. The elastic modulus is 190 GPa and Poisson's ratio is 0.3 for the material If stresses of 40 MPa and 75 MPa are applied in the x and y directions respectively, calculate the following: a) Change in sheet thickness, i.e. find At. Hint engineering and true strain are equal in the elastic regime. b) Sketch the shape of the circle after deformation on the figure below c) What is the elastic strain energy in the thickness direction only?
Q3 A plate of mild steel, 5 mm thick, 1000 mm long and 400 mm wide is stretched plastically 12% in the longitudinal direction. The characteristic stress-strain curve of the material is given by (o = 500 € 0.3 MPa). Assuming that the width is restrained from contracting by lateral end grips, calculate: a) final dimensions of the plate b) state of stress at the end of the stretching process c) final stretching load Assume no rolling pressure, and stress in the thickness direction = 0
1. What are the elastic modulus (E) and the Poisson's ratio () used to indicate? 2. Illustrate the differences between actual stress and engineered stress with strain, and also describe their underlying physical concepts. 3. If the engineering strain is 2% for a specific state of uniaxial stress, what is the real strain? Please solve for all in full detail and step by step
No wrong answer please , i could downvote The piece of suture is tested for its stress relaxation properties after cutting 3 cm long sample with a diameter of 1mm. The initial force recorded after stretching 0.1 cm between grips was 5 Newtons. Assume the suture material behave as if it has one relaxation time. The gage length was 1 cm. a. Calculate the initial stress. b. Calculate the initial strain. c. Calculate the modulus of elasticity of the suture if the initial stretching can be considered as linear and elastic. d. Calculate the relaxation time if the force recorded after 10 hours is 4 Newtons.
b) A metal wire is cold drawn from a radius of 5.75 mm to a radius of 3.25 mm. Compute the percent of the cold reduction in this process. (Ans: 68.05% c) A certain metal has a modulus of elasticity of 115 GPa, and its plastic deformation begins at a stress of 275 MPa. Calculate the maximum elongation to which it can be stretched without plastic deformation, if the metal has a length of 120 mm.
Q3: What is the magnitude of true strain (e) if the true stress (a) is 15% larger than engineering stress (0)?
A wire is drawn through a draw die with an entry angle = 15o. The starting diameter is 0.100 in. And the final diameter = 0.080 in. The coefficient of friction at the work-given interface = 0.07. The metal has a coefficient of resistance K = 30,000 psi and a strain hardening exponent of n = 0.20. Determine the stretching force and the stretching force in this operation.
A cylindrical specimen of brass that has a diameter of 20 mm, a tensile modulus of 110 GPa, and a Poisson's ratio of 0.35 is pulled in tension with a force of 40, 000 N. If the deformation is totally elastic and the original length is 120 mm, what is the shear modulus, G, of the specimen in GPa?
Circles of a metal are being punched that will be later stamped into coins. The metal has a shear strength of 32,575 psi. The sheets are 2.1 mm thick. The coin blanks are to be 16.5 mm in diameter. If sheet of metal is expected to produce 50 coin blanks, how much force is required to punch the sheets?
A cylindrical specimen of brass that has a diameter of 15 mm, a tensile modulus of 100 GPa, and a Poisson's ratio of 0.35 is pulled in tension with a force of 40, 000 N. If the deformation is totally elastic and the original length is 120 mm, what is the final diameter of the specimen in mm?
A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking, Take: Ac-0.06