A solid rectangular shaft of cross-section 80 mm x 50 mm is welded by a 5 mm fillet weld on all sides to a flat plate with axis perpendicular to the plate surface. Find the maximum torque that can be applied to the shaft, if the shear stress in the weld is not to exceed 85 MPa. Hint: T(max)= 4.242 T1 sx 1²

A solid rectangular shaft of cross-section 80 mm x 50 mm is welded by a 5 mm fillet weld on all sides to a flat plate with axis perpendicular to the plate surface. Find the maximum torque that can be applied to the shaft, if the shear stress in the weld is not to exceed 85 MPa. Hint: T(max)= 4.242 T1 sx 1²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 500 mm and a wall thickness of 6 mm. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 25 MPa. 50 O 2.63 MPa О 3.13 МРа О 3.36 МРа O 2.88 MPa O 2.44 MPa
A thin rectangular plate of dimensions 100 mm x 250 mm is formed by welding two triangular plates. The plate is subjected to a compressive stress of 2.5 MPa in longitudinal direction and a tensile stress of 12 .0 MPa in the transverse direction. Determine the normal stress ow acting perpendicular to the line of the weld and the shear stress Tw acting parallel to the weld. 12.0 MPa Weld -250 mm- 100 mm 2.5 MPa
The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tcircle/Tsquare of the shear stresses. Given: r = 15 mm, S = 22 mm, and t = 2.91mm.
6. A shaft of different diameters is planted to the wall at A and is subjected to torque loadings, as shown. Determine the maximum shear stress in the shaft. A fillet weld having a radius of 5 mm is used to connect the shafts at B. (note: the stress concentration diagram is given) 1000 N·m 50 mm B 400 N·m 30 mm 250 N·m 2.0 1.9 1.8 1.7 1.6 K 1.5 1.4 1.3 1.2 1.1 1.0 0.00 0.05 0.10 ▬▬▬▬▬▬▬▬▬▬▬ T D 0.15 LE 0.20 D/d=2.5 0.25 2.0 1.67 1.25 1.11 0.30
How many 8-mm diameter rivets is needed to fasten member DC to the gusset plate at Cif the member DC has thickness of 8 mm and the working stresses are 15 MPa for shear in the rivets and 20 MPa for bearing due to the rivets. Express your answer to the nearest whole number being the safe value of the rivets to be used. * Sm 40 RN 35 AN
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?
A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown below. The pressure in the tank is 2.76 MPa, and an axial load of 133.5 KN is applied to the end of the tank through a rigid bearing plate. Determine the normal stress and shearing stress perpendicular to the weld.
A 40 cm diameter steel tube is constructed with 0.5 cm thick welded plates, as shown in the illustration. If the tube is subjected to an axial tension load of 50 tons and a torque of 10 ton-cm, determine the normal and shear stresses acting in the plane of the weld, as shown in the figure. Express your answer in units of kgf / cm2. Consider that 1 ton = 1000 kgf.
A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.5 MPa in the x-direction and a tensile stress of 15 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. Lütfen birini seçin: a. 9.3175 MPa/6.09 MPa b. None c. 0.417 MPa/4.38 MPa d. 0.6256 MPa/6.70 MPa e. 11.874 MPa/6.70 MPa
7. For the stressed element in the following figure, determine (a) the value of ty for which the in-plane shearing stress parallel to the weld is zero, (b) the corresponding principal stresses. Represent the results on Mohr' s circle. 2 MPa Weld line Txy 75° 12 MPa
Solve Q7 only 4) A welded connection, as shown in Fig. 2, is subjected to an eccentric force of 60 kN in the plane of the welds. Determine the size of the welds, if the permissible shear stress for the weld is 200 N/mm2. 60 kN W3 100 W2 -150 50 Fig. 2 7) What is the value of polar moment of inertia of all welds about C.0.G? 3890094.64 mm4 4528724.56 mm4 6782459.89 mm4 9875612.79 mm4
If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d = 100 mm with 3 mm thick walls is T = 12 kNm, which of the following is closest to the magnitude of the minimum shear strain developed on that section? Select one: O A. 0.0072 rad O B. 0.0137 rad O C. 0.0128 rad O D. 0.0067 rad