B Consider the system given in the figure. The spring may sustain compressive as well as tensile forces, and its unstretched length is L/2. The mass of each bar is m₁, and m₂ is the mass of collar C. Bar AB is pinned from point A. Use Lagrange's equations to derive the equation of motion for 0. 'M Hint: Notice triangle ABC is an isosceles triangle, try to write position vectors for G and C in terms of 0

B Consider the system given in the figure. The spring may sustain compressive as well as tensile forces, and its unstretched length is L/2. The mass of each bar is m₁, and m₂ is the mass of collar C. Bar AB is pinned from point A. Use Lagrange's equations to derive the equation of motion for 0. 'M Hint: Notice triangle ABC is an isosceles triangle, try to write position vectors for G and C in terms of 0

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.10P: A cable and pulley system in the figure part a supports a cage of a mass 300 kg at B. Assume that...

See similar textbooks

Similar questions

A cable and pulley system in the figure part a supports a cage of a mass 300 kg at B. Assume that this includes the mass of the cables as well. The thickness or each of the three steel pulleys is t = 40 mm. The pin diameters are dPA= 25 mm, dB= 30 mm. and dc= 22 mm (see figure part a and part b). (a) Find expressions for the resultant forces acting on the pulleys at A, B. and C in terms of cubic tension T. (b) What is the maximum weight W that can be added to the cage at B based on the following allowable stresses? Shear stress in the pins is 50 MPa; bearing stress between the pin and the pulley is 110 MPa.
Repeat Problem 2.5-9 for the flat bar shown in the figure but assume that and that
A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo is unloaded by a container handling crane. Each bollard is fastened to the wharf using anchor bolts. Three cables having known tension force magnitudes F, = ll0 kN.F, = 85kN.and F, 9OkNare secured to one bollard at a point A with coordinates (0.0.45 m. 0) in the x-r-: coordinate system shown in the figure part b. Each cable force is directed at an attachment point on the ship. Force F, is directed from point A to a point on the ship having coordinates (3 m, 9 m. 0) force F, is directed at a point with coordinates (6.5 m. 8.5 m. 2 m) and force F, is directed at a point with coordinates (8 m. 9 m. S m). The diameter of each anchor bolts is 4 24 mm. (a) Find the reaction forces and reaction moments at the base of the bollard. (b) Calculate the average shear stress in the anchor bolts (in the x-: plane). Assume each bolt cart ics an equal share of the total force.
Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10 lb.
Find the magnitude of tension in string (or spring scale reading) and the magnitude of vertical FV and horizontal FH components of force applied on meter stick by the hinge. (Project this equation on Ox …this will give you the magnitude of FH force. Project this equation on Oy …this will give you the magnitude of FV force) (Draw a free body diagram) please data: Lruler = 1m mruler= 134 g dstring=80 cm d1= 35 cm d2= 82 cm M1=250g M2=150g θ = 38 degrees α= 62 degrees
A weight W= 120 kN is being supported by steel sections with force T, force F, andforce C. The coordinates of A, B, C, and D are given. Assume that E is the origin(0,0,0). Determine Forces T, F, and C. (Hint: Produce three equations fromequilibrium of force system)Note: The Forces T, F, and C must be computed accurately to design the proper sizes ofsteel sections in the subject “Steel Design.”
PConsider the following spring system. with spring constants c 3 Assume down is the positive direction. Write the stiffness matrix K 10 Compute the displacements caused by the external forces f -2 Displacement =
GIVEN: DISTANCES CO= 7m BO= 7m OD= 8m AD= 8m GIVEN: WEIGHT W1= 195 N W2= 295 N GIVEN: ANGLE X= 55 Degree Y= 48 Degree SOLVE: (a) Tension at CB in NEWTON (b) Reaction at point O in NEWTON PLS PLS SOLVE AND SHOW COMPLETE SOLUTION AND WRITE LEGIBLY. ALSO, DRAW THE FREE-BODY DIAGRAM. ROUND OFF IN 4 DECIMAL PLACES.
Q: For the spring system shown in the accompanying figure, determine the displacement of each node. Start by identifying the size of the global matrix. Write down elemental stiffness matrices, and show the position of each elemental matrix in the global matrix. Apply the boundary conditions and loads. Solve the set of linear equations. Also, compute the reaction forces. k2 = 9 lb k1 = 20b in 20 lb k,=5 lb ww lb in kz = 5 lb in ks = 9 in lb k6 = 9 in 50 lb k4 = 20 lb kg = 20 b in in
Q1: In the below drawings, three unbalanced masses and related details are provided. Please answer the following questions. a) a balancing mass is to be located at rp = 50 mm, then what would be the balancing m1 m1 650 mm 200 mm m2 mass (m,) and its angular position (Op) (Please use the r2 m2 A graphical method) r3 m3 15 m3 b) If the system is not balanced what would be the reaction forces at A and B. (FA, FB=?) n = 150 rpm r; = 30 mm m, = 1 kg r2 = 20 mm 40 тm 13= m, =3 kg m; = 2 kg k = please choose an appropriate scaling factor yourself SHOT ON MI 6 MI DUAL CAMERA
The linkage shown is used in a vehicle suspension system. Find the forces indicated below when a static force of F = 820 lb is applied to the tire at point C at an angle of 0 = 22° as shown. Assume the connection of the wheel to member AB is rigid. hs hy hi F BY NC SA W4. W, Ws 2013 Michael Swanbom Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value Variable Value hi 10 in Wi 8.8 in h2 15.6 in W2 5.6 in h3 18.1 in W3 10.8 in h4 10.9 in WĄ 7.4 in h5 4.9 in W5 9.3 in For all answers, take x as positive to the right and y as positive upward. At point B, member AB exerts a force of B = j lbs on member BHE. At point A, member AD exerts a force of A + j lbs on member AB. At point H, shock GH exerts a force of H = i + i lbs on member ВНЕ. At point E, the magnitude of the force exerted on the car body by member BHE is lbs. At point D, the magnitude of the force exerted on the car body by member AD is lbs. At point G, the…
perpendicular to the page through the point o. (Let counterclockwise torque be positive and let forces to the right and up be positive. Use the following as necessary: the forces R, Write the necessary equations of equilibrium of the object shown in the figure below. Take the origin of the torque equation about an axis RFF, and F the length l of the object; and the angle e that the object makes with the horizontal.) EF, = = 0 Fy =0 Στ. =0 Need Help? Read It