Answered: dam spillway is to be tested using…

dam spillway is to be tested using Froude scaling with a 1:20 model. The model flow has an average velocity of 0.7 m/s. What is the velocity of prototype?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Related questions

Q: 05: A prototype ship is 35 m long and designed to cruise at 11 m/s. Its drag is to be simulated by a…

Q: (a) Discuses three necessary conditions for complete similarity between a model and a prototype in…

A: a. A model and a prototype complete similarity is depicted by considering following three…

Q: The population P in thousands of Tallahassee, Florida, from 2000 through 2014 can be modeled by P =…

A: Given, P=150.9ekt Note: P is in thousands, which means if P=1, the population is 1000. a) At yeat…

Q: A one-fourth scale model of an airplane is to be tested in water. The airplane has a velocity of 700…

Q: Question 1 A ramp is made by leaning a track against a few textbooks. A cart Is Set track and rolls…

Q: The following data was obtained from wind tunnel testing of a scale model: Air speed (m/s) Drag…

A: The following data was obtained from wind tunnel testing of a scale model: Air speed (m/s) Drag…

Q: A 1:30 model of a ship is made. The real ship has a hull length of 130 m and travels at 7.9 m/s.…

Q: For studying of a dam in the laboratory, a model overflow has been built in the scale of , to 36…

A: (i) The scale ratio of the model to prototype is given as, The flow rate of the model is given as,…

Q: Case 1: Material system without density and viscosity differences Though unlikely in real life,…

A: given; Material system without density and viscosity differences

Q: A dam 65 ft wide with a nominal flow rate of 260 ft3/s is to be studied with a scale model 3 ft wide…

A: Given Flow rate = 260 ft3/s Scale = 3 ft Calculate the flow rate…

Q: Wind blows and pasts a banner causes it to flutter. The fluttering frequency f is a function of the…

A: Given: Fluttering frequency is a function of following variables: ω=fnV,ρ,g,L,ρA Length of the…

Q: Flow Characteristics (Entrance flow) Why was not the linear regression applied to all of the…

A: Linear regression basically tells us the esteem of the dependent variable for a subjective…

Q: Use this information to answer Questions 1-8 below. The following table gives data relating a car's…

A: (1) Calculate the value of fuel efficiency by using given model.…

Q: A student team is to design a human-powered submarine for a design competition. The overall length…

A: According to the information we have A team of students design a powerful human submarine for a…

Q: A 60-ft-long "check dam" on a river provides a means of collecting debris that flows downstream. The…

Q: The following shear stress - shear rate behavior was observed. Shear rate (Seconds¬') Shear Stress…

A: According to the question, τ=K∂u∂ynτ=shear stressK=consistency index∂u∂y=strain raten=Flow behaviour…

Q: Determine if the data has a positive or a negative relationship with each other. Showcase the…

A: .

Q: In the field of air pollution control, one often needs to sample the quality of a moving airstream.…

A: Given Data:

Q: The pressure difference ∆p produced by a water pump, and the power P required to operate it,…

A: Solution:- Given that:- ∆P & P=fD, φ,ω,ρ,μ → I Where, ∆P=Pressure difference…

Q: For a set of experimental data of (x, yi), i = 1, .,n, the theoretical analysis suggests that the…

A: Given that y = A xm exp( B x2)

Q: In order to fest the flow the surface of an airplane wing, a model is built to a scale of 1/17 and…

A: First, calculate the dynamic viscosity of water at 20 degree-Celcius as follows.

Q: About supervised machine learning, in the context of Linear Regression; Decision tree; Logistics…

A: A classification model tries to make some sort of judgement based on the training input values.…

Q: As an industrial engineer, you intend to use linear trend (or linear regression) method to solve a…

Q: How do you determine which type of trendline to use on a graph? The accepted or proposed…

A: The best fit parameter value (R2) is the type of trendline to use in graph

Q: External Problem 1: Dimensional analysis and similarity A fighter aireraft is to operate at 200 m/s…

A: Given: Velocity of the prototype (Vp)=200m/sDensity of the fluid in prototype (ρp)=1.2kg/m3Scale…

Q: According to Froude scaling laws, what should the revolutions per minute of the prototype propeller…

Q: A certain small river has an average width of 60 feet and a depth of 4 feet.This river carries water…

A: Froude number Fr =vgl

Q: In a biological study you count the following number of predators passing a camera each night:…

Q: An airplane wing model is designed with a similarity test. The lift force is a function of speed,…

Q: Problem 2 A major automotive company wants to use wind tunnel experiments to estimate the…

A: (a) The given relationship between the variables is Let us consider the linear equation,

Q: An underwater device which is 2m long is to be moved at 4 m/sec. If a geometrically similar model 40…

A: By pressure modelling - PprototypePmodel= ρV2prototypeρV2modelPatmPmodel=…

Q: A surface vessel is 156 m long and moves at a velocity of 6.83 m/s. Determine the velocity of a…

A: Length, Lp = 156 m Length, Lm= 2.44 m Velocity Vp = 6.833 m/s Calculate the velocity of the model…

Q: . An submarine is to be designed for underwater exploration in the seas of Leyte. The overall length…

A: Reynolds number is a dimensionless parameter that is used to determine the dynamic characteristics…

Q: A one-fortieth-scale model of a ship’s propeller is tested in a tow tank at 1250 r/min and exhibits…

A: Given:Model scale ratio, α=140Revolutions per minute of model , Ωm=1250 r/minPower exhibits by…

Q: Question 2 A process instrument reading Z (volts) is thought to be related to a process stream flow…

A: Given dataZ=avbpcwhereZ is in voltsV is stream flow rate in msP is pressure in KPaTo find the…

Q: 1) To ensure complete similarity, the model and prototype must be a) same material b) similar…

A: 1 . to ensure complete similarity between model and prototype must be option [ b] similar…

Q: A dimensional analysis is performed on the drag on a boat. When the effects of viscosity can be…

Q: A model is built to a scale of 1:15. The model is tested in a laboratory with a velocity of 0.80 m/s…

A: (a) the velocity on the prototype. VPVm=LPLmVP0.80=15VP=3.1 ms

Q: A dam 75 ft wide, with a nominal flow rate of 260 ft 3 , is tobe studied with a scale model 3 ft…

A: Dam widthLreal=75 feetnominal flow rate Qmodel=260 ft3tmodel width =3 feet

Q: Upon completion of the Reynolds experiment, we had this information. The tube diameter was 0.03 m,…

A: Given:d=0.03 mt=14 secQ=21*10-6 m3/sμ=0.8701*10-3 Pa.sT=26°CA=π4*0.032A=7.06858*10-4…

Q: (2 of 2) Air flows through a single-stream, steady-flow device. At thế flow rate is 3.4 kg/s and the…

Question

100%

A dam spillway is to be tested using Froude scaling with a 1:20 model. The model flow has an average velocity of 0.7 m/s. What is the velocity of prototype?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A prototype spillway has a characteristic velocity of 3 m/sand a characteristic length of 10 m. A small model is constructedby using Froude scaling. What is the minimumscale ratio of the model that will ensure that its minimumWeber number is 100? Both flows use water at 20 ° C.
7. An oil (sp.gr 0.9) is flowing through a 1.2m diameter pipe at a rate of 2.5 m³/s. The kinematic viscosity of oil is 3 X106 m²/s. In order to model this flow, water is used to flow through a 120mm diameter pipe having kinematic viscosity of 0.012X104 m²/s. Find the model discharge and velocity.
A 1:30 model of a ship is made. The real ship has a hull length of 130 m and travels at 7.9 m/s. Find the fraude number. If there is a dynamic similarity and froude # criterion applies, what should the velocity of the mdoel ship be?
4. The water velocity at a certain point along a 1:10 scale model of a dam spillway is 5 m/s. What is the corresponding prototype velocity if the model and prototype operate in accordance with Froude number similarity? (Ans: 15.8 m/s)
Here, a 1:10 scale prototype of a propeller on a ship is to be tested in a water channel. What would the rotating speed of the model be if the rotational speed of the p propeller is 2000 rpm, and if: (a) the Froude number governs the model-prototype similarity(b) Reynolds number governs the similarity
A dam 75 ft wide, with a nominal flow rate of 260 ft 3 , is tobe studied with a scale model 3 ft wide, using Froude scaling.( a ) What is the expected flow rate for the model?( b ) What is the danger of only using Froude scaling for thistest? ( c ) Derive a formula for a force on the model as comparedto a force on the prototype.
Q4: Use dimensional analysis to show that in a problem involving shallow water waves (Figure 1), both the Froude number (Fr T) and the Reynolds number %3| Vgh (Re = pch are relevant dimensionless parameters Fr = f (Re). The wave speed c of waves on the surface of a liquid is a function of depth h, gravitational acceleration g, fluid density p, and fluid viscosity u. P.u Figure 1
Q4: Use dimensional analysis to show that in a problem involving shallow water waves (Figure 1), both the Froude number (Fr = and the Reynolds number (Re pch. are relevant dimensionless parameters Fr = f (Re). The wave speed c of %3D waves on the surface of a liquid is a function of depth h, gravitational acceleration g, fluid density p, and fluid viscosity u. P. u Figure 1
04: Use dimensional analysis to show that in a problem involving shallow water waves (Figure 1), both the Froude number (Fr T) and the Reynolds number Vgh (Re = pch. are relevant dimensionless parameters Fr = f (Re). The wave speed c of waves on the surface of a liquid is a function of depth h, gravitational acceleration g, fluid density p, and fluid viscosity µ. Figure 1
A dam 74 ft wide with a nominal flow rate of 260 ft3/s is to be studied with a scale model 3 ft wide using Froude scaling. What is the expected flow rate for the model? Derive the formula for a force on the model as compared to a corresponding force on the prototype.
A prototype ocean platform piling is expected to encountercurrents of 150 cm/s and waves of 12-s period and 3-mheight. If a one-fifteenth-scale model is tested in a wavethe channel, what current speed, wave period, and wave heightshould be encountered by the model?
b) The following shear stress – shear rate behavior was observed. Shear rate (Seconds-1) Shear Stress (dynes/cm?) 20 11 30 15.2 40 19.1 50 22.9 60 26.5 1. Make a plot of shear stress (ordinate) vs shear rate (abscissa) on log-log paper. 2. Can the fluid behavior be accurately modeled by the Newtonian, Bingham plastic, or Power law model?