E Problem Number A 3.5 in 4.25 in 6 in TI 8 in 10 1500 psi Bolt grade B C D E F N Pr Bolt spec. 8-34 in (h) Calculate the maximum stress in the bolt. (i) Calculate the torque required to establish the bolt preload. SAE 5 in-13 An end plate is loaded by the gas pressure inside a pipe. N is the total number of bolts. Assume the pipe / plate material is ASTM A36 steel. The bolts are 2.0 inches long with a threaded length of 1.25 inches. The nut thickness is 0.50 inches. For the data specified in column 8-34: (a) Determine the force on the end plate. (b) Calculate the nominal force per bolt w/o preload. (c) Calculate the nominal stress in the bolt w/o preload. (d) Calculate the connection / joint stiffness. (e) Calculate the bolt stiffness. (f) Assuming safety factor of Q = 1.25 for the connection, calculate the required bolt preload. (g) Calculate the maximum force in the bolt.

E Problem Number A 3.5 in 4.25 in 6 in TI 8 in 10 1500 psi Bolt grade B C D E F N Pr Bolt spec. 8-34 in (h) Calculate the maximum stress in the bolt. (i) Calculate the torque required to establish the bolt preload. SAE 5 in-13 An end plate is loaded by the gas pressure inside a pipe. N is the total number of bolts. Assume the pipe / plate material is ASTM A36 steel. The bolts are 2.0 inches long with a threaded length of 1.25 inches. The nut thickness is 0.50 inches. For the data specified in column 8-34: (a) Determine the force on the end plate. (b) Calculate the nominal force per bolt w/o preload. (c) Calculate the nominal stress in the bolt w/o preload. (d) Calculate the connection / joint stiffness. (e) Calculate the bolt stiffness. (f) Assuming safety factor of Q = 1.25 for the connection, calculate the required bolt preload. (g) Calculate the maximum force in the bolt.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter22: Welding Joint Design And Welding Symbols

Section: Chapter Questions

Problem 4R: Sketch a V-grooved butt joint, and label all of the joint's dimensions.

See similar textbooks

Similar questions

Figure 8-19 is a cross-section of ASTM A36. A total of N bolts are to be used to resist a separating force of 7258.97N is one bolt. A) Determine kb,km, and C B) Determine the realized load factor for overload, the yielding factor of safety, and the load factor of joint separation.
As shown in figure below, two plates are clamped by washer-faced 2 in-20 UNF SAE grade 5 bolts each with a standard 2 N steel plain washer. The top plate is steel and the bottom pplate is gray cast iron. If a total of 8 bolts where used to close 1 feet diameter pipe which applied at maximum pressure of 150 psi. Calculate the static and fatigue safety factor of this joint. Used Goodman theory for tha fatigue safety 1/2 factor. 3/4
Two identical aluminum plates are each 3 in thick, and are compressed with one bolt and nut. Washers are used under the head of the bolt and under the nut. Washer properties: steel; ID = 0.531 in; OD = 1.062 in; thickness = 0.095 in Nut properties: steel; height = 7/16 in Bolt properties: 1/2 in-13 UNC grade 8 Plate properties: aluminum; E = 10.3 Mpsi; Su = 47 kpsi; Sy = 25 kpsi (a) Determine a suitable length for the bolt, rounded up to the nearest 1/4 in. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members.
Sketch a V-grooved butt joint, and label all of the joint's dimensions.
Qestion-1: A 9/16 in UNF bolt is subjected to a load P = 60 kip in a tension joint as shown in Figure. The bolt is SAE grade 5 and lubricated. The initial bolt tension (F) = 35 kip. The bolt and joint stiffnesses are k, = 6.5 and km 10.8 Mlbf/in Note: Use the related tables, formulas and concepts to answer following question (a) Formulate to determine the preload and service load stresses in the bolt. (b) Solve to find the torque necessary to develop the preload. (c) Identify if the bolt will fail or no under preload and service load stresses (Calculated in part a) by comparing with the SAE minimum proof strength of the bolt. (d) Can you identify; with given input data, tables and formulas that bolt is self-locking? Table 8-9 SAE Specifications for Steel Bolts Size SAE Range Grade Inclusive, No. in +14 1 2 4 5 5.2 7 8 TI I LI I I I +-14 8.2 -1 Minimum Proof Strength," kpsi 33 55 33 65 85 74 85 105 120 120 Table 8-2 Diameters and Area of Unified Screw Threads Size Designation 0 1 2 3 4…
-.3: Draw the front view for a square-headed bolt and a square neck with a castle nut and a washer in position. Take the bolt diameter is 24mm and length is 100mm.(use ISO metric threads) Your answer •ns: Draw the two views (front and top) of a two plates (thickness 5 mm) joined by a single riveted , double strap butt joint. use a Round top countersunk head for the rivet( see Figure). The curve of the head R=1.0606*d 1.5 d 0.2 d 0.25 d
Problem 3: A Hexagonal bolt connects two members. The joint has a gap 1 = 2 in and the applied load is 2000 lb. Both of the clamped parts are steel. A preload of 90% the bolt's proof strength will be applied first. For this design, an SAE grade 1, 5/16"-18 UNC-2A bolt is chosen made from A307 with rolled threads. Washers are included between the head and the joint, and between the nut and the joint. Determine a suitable length for the bolt? Find its safety factor against yielding and against joint separation. Are these values acceptable?
3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.
Required information For a bolted assembly with six bolts, the stiffness of each bolt is kb 2 Mibf/in and the stiffness of the members is km = 13 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. It is desired to find the range of torque that a mechanic could apply to initially preload the bolts without expecting failure once the joint is loaded. Assume a torque coefficient of K = 0.2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts once the load is applied. The maximum bolt preload that can be applied is Ibf.
If Equation 2j-3>m , where 'j' is number of joints, 'm' is no of members , frame is a
Find the size of 14 bolts required for C.I.steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm.
Statement: The figure below shows three cycles of time-varying loading on a double D-ring held together with a single bolt and nut. The figure shows both the bolt tensile force and the member compressive force. QUESTION 1 - Based on the figure, give the minimum and the maximum of the external load, P?