Assume that the circuit in Figure 18-1 has a power factor of 78%, an apparent power of 374.817 VA, and a frequency of 400 Hz. The inductor has an inductance of 0.0382 H.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The missing values in the table.
Answer to Problem 4PP
ET = 150.062 V | ER = 150.062 V | EL = 150.062 V |
IT = 2.498 A | IR = 1.948 A | IL = 1.563 A |
Z = 60.073 Ω | R = 77.024 Ω | XL = 96.007 Ω |
VA = 374.817 | P = 292.357 W | VARSL = 234.55 |
PF = 78% | L = 0.0382 H |
Explanation of Solution
Given data:
The inductive reactance XL is calculated as,
Using the Power factor (PF) and Apparent Power(VA), we can calculate True Power (P) as,
The reactive power VARSL is calculated as,
The relation between reactive power, voltage and inductive reactance is given as,
Since the circuit is parallel R-L,
The current through the inductor is,
The relation between true power P, voltage ER and resistance R is given as,
The current through the resistor is,
The current through the inductor is,
The total current in the circuit
The impedance Z is calculated as,
Power factor angle θ will be,
Want to see more full solutions like this?
Chapter 18 Solutions
Delmar's Standard Textbook Of Electricity
- QUESTION 19 E-06, PC-02. Three inductors 15 mH, 15 mH and 15 mH are connected in series. What is the total inductance? O 5 mH. Without knowing the coupling factor the total inductance cannot be found. 45mH. QUESTION 20 E-06, PC-05. Why are the iron cores of most induction coils laminated? To increase the core permeability. O To reduce the core reluctance. O To reduce the effects of eddy currents. Click Save and Submit to save and submit. Click Save All Answers to save all answers. MacBook Air 888 F7 FB F6 F4 F3 F2 & 23 $ 4 5 0 8 3 Y W E と S D S F G >> J しの く つ つ >arrow_forwardImpedance questionarrow_forwardarcing carrow_forward
- in lab winding schemes, The-2 induced emf in a coil is emf in .coil for wave winding a) greater than b) smaller than O c) equal to Oarrow_forwardQUESTION FIVE The boost regulator has an input voltage, V = 9 V. The average output voltage, Va = 15 V and average load current, la = 0.8 A. The switching frequency is 20 kHz. If L = 300µH and C = 440µF, determine (a) the duty cycle 8 (b) the ripple current of inductor, AI, (c) the peak current of inductor, I₁, (d) the ripple voltage of filter capacitor,AVC, and (e) the critical values of L and C.arrow_forwardq24 Match the following choose the correct answer Electromagnetic interference .controls voltage at all level scarry inrush current for short period disturbance of frequency around 10MH zzoning regulations shunt or series capacitors High voltage DC Transmission prevents complete shutdown cost of insulation is more Reactive power compensation .controls voltage at all level scarry inrush current for short period disturbance of frequency around 10MH zzoning regulations shunt or series capacitors High voltage DC Transmission prevents complete shutdown cost of insulation is more Tap changing transformers . .controls voltage at all level scarry inrush current for short period disturbance of frequency around 10MH zzoning regulations shunt or series capacitors High voltage DC Transmission prevents complete shutdown cost of insulation is more Single bus bar with sectionalisation ...controls voltage at all level scarry inrush current for short period disturbance of…arrow_forward
- 6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current hearrow_forwardRotationalarrow_forwardQuestion 1.) Fill in the blanks with proper wording a.) For a purely resistive circuit, the voltage and current phasors are b.) For a purely inductive circuit, the voltage and current phasors are c.) For a purely capacitive circuit, the voltage and current phasors arearrow_forward
- D.C shunt generators are most suitable for arc windingarrow_forwardThe rotor winding of the induction motor at no load condition is equivalent to connected to an inductive load short circuited connected to a resistive load O open circuitedarrow_forwardFacts A clipper is a device that removes either the positive half (top half) or negative half (bottom half), or both positive and negative halves of the input AC signal. In other words, a clipper is a device that limits the positive amplitude or negative amplitude or both positive and negative amplitudes of the input AC signal. In some cases, a clipper removes a small portion of the positive half cycle or negative half cycle or both positive and negative half cycles. In the below circuit diagram, the positive half cycles are removed by using the series positive clipper. Question: In your own opinion. Why do we need to clip a certain amount of voltage in positive or negative or on both sides? What is the benefit of that in our devices or circuits in doing such thing?arrow_forward
- Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage LearningPower System Analysis and Design (MindTap Course ...Electrical EngineeringISBN:9781305632134Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. SarmaPublisher:Cengage Learning